Bunks & Brackets

2"X6" Carpeted Bunks

10 sizes available

2"x2" 84" Track 67" SC Straight Axles

2X2X84TR 67SC 5L HD W/BRK. FLANG

2"x2" 91"Track 73"SC Straight Axles

2 sizes available

2X4 PLASTIC COVER BUNK[GREY]

5 sizes available

2X6 PLASTIC COVER BUNK[GREY]

7 sizes available

300-03156-GL ~ FENDER BRACKET GALVANIZED TRAILERS 37" FENDERS KARAVAN

REPRESENTATION PHOTO MAGIC TILT FENDER BRACKETS ~ 300-03156-GL MOUNTS WITH U-BOLTS OVER TUBE FRAME USED WITH 37" PLASTIC FENDERS FOR 12" AND 13" TIRES

300-03758-GL ~ FENDER BRACKET GALVANIZED TRAILERS 40" FENDERS KARAVAN

REPRESENTATION PHOTO MAGIC TILT FENDER BRACKETS ~ 300-03758-GL MOUNTS WITH U-BOLTS OVER TUBE FRAME USED WITH 40" PLASTIC FENDERS FOR 14" TIRES

300-03858-GL ~ FENDER BRACKET ALUMINUM TRAILERS 37" FENDERS KARAVAN

REPRESENTATION PHOTO MAGIC TILT FENDER BRACKETS ~ 300-03858-GL MOUNTS WITH PY1701 BOLTS UNDER ALUMINUM TUBE FRAMES USED WITH 37" PLASTIC FENDERS FOR 12" AND 13" TIRES

3X10 BUNK W/CARPET

4 sizes available

3X6 BUNK W/CARPET

5 sizes available

3X8 BUNK W/CARPET

7 sizes available

7/16" Bunk Bracket UBolts W/Nuts

Part Qty PY1406 NUT HEX 7/16 HDG 2 PY1515 WASHER FLAT USS 1/2 HDG 2 PY1606 WASHER LOCK 7/16 HDG 2 PY2090 UBOLT 7/16X3-1/16X2-13/16 SQ GALV 1

Aluminum Cross-member "L" Brackets

2 sizes available

Angles for Single Axle

7 sizes available

Bolster Dimpled Bunk Brackets

6 sizes available

Bow Board Kits

2 sizes available

Bunk Risers

Cross-member "L" Brackets W/Brace

2 sizes available

Custom Step Pads

2 sizes available

End Caps Bell

12 sizes available

Fender Brackets

4 sizes available

Galvanized Cross-member "L" Brackets

4 sizes available

6" X-ARM-L VERTICAL BUNK BRACKET, GALV, 8-HOLE

Galvanized Plates

2-HOLE PLT.[PWC-4 BACKING PLT.]

Grey Carpet

6 sizes available

Guide Brackets

GUIDE-ON BRACKET [EACH]

PI0100 ~ FENDER BRACKET GALVANIZED

MAGIC TILT FENDER BRACKETS ~ PH0100 SOLD INDIVIDUALLY

PI2100 ~ STEP PAD END CAP RIGHT/FRONT OR LEFT/REAR "L"

REPRESENTATION PHOTO THE CORRECT STEP PAD ORIENTATION IS WITH THE FLAT EDGE TO THE FENDER AND THE SMOOTH SLANTED EDGE AWAY FROM THE FENDER. THIS IS HOW YOUR BOOT WILL BE ORIENTED BASED ON THE LOCATION STATED. IF YOU WANT YOUR BOOT MOUNTED THE OPPOSITE WAY, PLEASE SELECT THE OPPOSITE SIDE. MAGIC TILT STEP PAD BOOT ~ PI2100 SOLD INDIVIDUALLY ATTACHING SCREW OR RIVET NOT INCLUDED HAS "L" STAMPED ON INSIDE

PI2110 ~ STEP PAD END CAP LEFT/FRONT OR RIGHT/REAR "R"

REPRESENTATION PHOTO THE CORRECT STEP PAD ORIENTATION IS WITH THE FLAT EDGE TO THE FENDER AND THE SMOOTH SLANTED EDGE AWAY FROM THE FENDER. THIS IS HOW YOUR BOOT WILL BE ORIENTED BASED ON THE LOCATION STATED. IF YOU WANT YOUR BOOT MOUNTED THE OPPOSITE WAY, PLEASE SELECT THE OPPOSITE SIDE. MAGIC TILT STEP PAD BOOT ~ PI2110 SOLD INDIVIDUALLY ATTACHING SCREW OR RIVET NOT INCLUDED HAS "R" STAMPED ON INSIDE

PIVOT L BRACKETS

3 sizes available

PK1200 ~ 3-HOLE PLATE GALVANIZED

REPRESENTATION PHOTO MAGIC TILT 3-HOLE PLATE ~ PK1200

PK1205 ~ 3-HOLE BUNK PLATE GALVANIZED

REPRESENTATION PHOTO MAGIC TILT 3-HOLE BUNK PLATE ~ PK1205

PK1250 ~ 5-HOLE PLATE GALVANIZED

REPRESENTATION PHOTO MAGIC TILT 5-HOLE PLATE ~ PK1250

PK1320 ~ 1-HOLE SLOT PLATE GALVANIZED

REPRESENTATION PHOTO MAGIC TILT 1-HOLE SLOT PLATE ~ PK1320

PK2512 ~ 1-AXLE UNDERCARRIAGE 38" 2-EYE INSIDE MOUNT

REPRESENTATION PHOTO SPECIAL ORDER. PLEASE ALLOW ADDITIONAL TIME. MAGIC TILT UNDERCARRIAGE ~ PK2512 WILL WORK ON EITHER LEFT OR RIGHT SIDE 31" BETWEEN STEP MOUNTS USED ON ALUMINUM FRAME TRAILERS HOLE SIZE FOR MOUNTING TO FRAME: 1/2" ON 4-1/4" CENTERS BOLT PATTERN FOR MOUNTING TO FRAME MAY NOT MATCH EXISTING UNDERCARRIAGE AXLE & SPRING-TO-UNDERCARRIAGE HARDWARE KITS: 2x2 AXLES: GALVANIZED PK1100 , STAINLESS/GALV PK1100-SS 2x3 AXLES: GALVANIZED PK1100-1

PK2513 ~ 1-AXLE UNDERCARRIAGE 38" 2-EYE OUTSIDE MOUNT

REPRESENTATION PHOTO MAGIC TILT UNDERCARRIAGE ~ PK2513 WILL WORK ON EITHER LEFT OR RIGHT SIDES 31" BETWEEN STEP MOUNTS USED ON ALUMINUM FRAME TRAILERS HOLE SIZE FOR MOUNTING TO FRAME: 1/2" BOLT PATTERN FOR MOUNTING TO FRAME MAY NOT MATCH EXISTING UNDERCARRIAGE AXLE & SPRING-TO-UNDERCARRIAGE HARDWARE KITS: 2x2 AXLES: GALVANIZED PK1100 , STAINLESS/GALV PK1100-SS 2x3 AXLES: GALVANIZED PK1100-1

PK2655 ~ 2-AXLE UNDERCARRIAGE 71" 68" FENDERS FOR ALUMINUM STEPS

Magic Tilt Undercarriage ~ PK2655 Good to know: Primarily used on aluminum i-beam trailers Hole size for mounting to frame: 1/2" On 4-1/4" Centers Bolt pattern for mounting to frame may not match existing undercarriage Axle & Spring-to-undercarriage hardware kits: 2x2 Axles: Galvanized PK1150 , Stainless/Galv PK1150-SS 2x3 Axles: Galvanized PK1152 , Stainless/Galv PK1152-SS

PK2658 ~ 2-AXLE UNDERCARRIAGE 71" 60" FENDERS FOR ALUMINUM STEPS

REPRESENTATION PHOTO MAGIC TILT UNDERCARRIAGE ~ PK2658 PRIMARILY USED ON ALUMINUM I-BEAM TRAILERS FOR PONTOON BOATS HOLE SIZE FOR MOUNTING TO FRAME: 1/2" ON 4-1/4" CENTERS BOLT PATTERN FOR MOUNTING TO FRAME MAY NOT MATCH EXISTING UNDERCARRIAGE AXLE & SPRING-TO-UNDERCARRIAGE HARDWARE KITS: 2x2 AXLES: GALVANIZED PK1150 , STAINLESS/GALV PK1150-SS 2x3 AXLES: GALVANIZED PK1152 , STAINLESS/GALV PK1152-SS

PK2770 ~ 3-AXLE UNDERCARRIAGE 112" WITH STEPS

REPRESENTATION PHOTO (PLEASE CALL 941-358-1117 FOR SHIPPING QUOTE) MAGIC TILT UNDERCARRIAGE ~ PK2770 NO FRAME MOUNTING HOLES USED ON ALUMINUM AND GALVANIZED TRAILERS USES U-BOLTS TO GO AROUND TUBE OR C-CHANNEL FRAMES (NOT INCLUDED) AXLE & SPRING-TO-UNDERCARRIAGE HARDWARE KIT: PK1153

PK2775 ~ 3-AXLE UNDERCARRIAGE 120" WITH STEPS

REPRESENTATION PHOTO (PLEASE CALL 941-358-1117 FOR SHIPPING QUOTE) MAGIC TILT UNDERCARRIAGE ~ PK2775 USED ON ALUMINUM AND GALVANIZED TRAILERS USES U-BOLTS TO GO AROUND TUBE OR C-CHANNEL FRAMES (NOT INCLUDED) AXLE & SPRING-TO-UNDERCARRIAGE HARDWARE KIT: PK1153

PL2550 ~ LICENSE TAG BRACKET

REPRESENTATION PHOTO MAGIC TILT LICENSE TAG BRACKET ~ PL2550 MOUNTS BETWEEN LEFT TAIL LAMP AND TAIL LAMP MOUNTING BRACKET

Plastic Bunk Cover

4 sizes available

Plush Black Carpet

4 sizes available

PO1980 ~ BOW STOP "U" BRACKET

REPRESENTATION PHOTO MAGIC TILT "U" BRACKET ~ PO1980 DOES NOT INCLUDE MOUNTING HARDWARE , PM1000 WINCH , ROLLER

PP2245 ~ RUB STRIP WITH HOLES 4" x 10" x 3/8"

REPRESENTATION PHOTO MAGIC TILT RUB STRIP ~ PP2245 INCLUDES 4 SELF TAPPING MOUNTING SCREWS REPLACEMENT CENTER PAD FOR PV2280-3 ASSEMBLY PRE-DRILLED HOLE PATTERN NOT GUARANTEED TO MATCH OLDER HOLE PATTERN SOAK STRIP IN HOT WATER PRIOR TO INSTALLATION

PP2258 ~ BUNK SLIDE 3/8" x 12" x 8'

REPRESENTATION PHOTO MAGIC TILT BUNK SLIDE ~ PP2258 (PLEASE CALL 941-358-1117 FOR SHIPPING QUOTE AND TO ORDER) PREMOLDED WITH VEE DOWN CENTER NO HOLES MOUNTING HARDWARE NOT INCLUDED

PP2260 ~ RUB STRIP 3 x 2

REPRESENTATION PHOTO MAGIC TILT RUB STRIP ~ PP2260 MOUNTING HARDWARE NOT INCLUDED MOUNTED WITH RIVETS FROM FACTORY CAN BE MOUNTED WITH TWO PY0491 SCREWS

PP2270 ~ RUB STRIP 1-3/4 x 15

REPRESENTATION PHOTO MAGIC TILT RUB STRIP ~ PP2270 CAN BE TRIMMED TO DESIRED LENGTH MOUNTING HARDWARE NOT INCLUDED MOUNTED WITH RIVETS FROM FACTORY CAN BE MOUNTED WITH THREE PY0491 SCREWS

PQ1600 ~ ROLLER END CAP WHEEL 8-1/2" (STOLTZ)

REPRESENTATION PHOTO MAGIC TILT END CAP WHEEL ~ PQ1600 SOLD INDIVIDUALLY OFTEN USED ON SKIFFS OR ANY BOW WITH A LARGE PROTRUSION WHERE ADDITIONAL STANDOFF IS REQUIRED.

PQ1650 ~ BOW STOP ROLLER ASSEMBLY 8"

REPRESENTATION PHOTO MAGIC TILT ROLLER ASSEMBLY ~ PQ1650 * SELECT INNER ROLLER LENGTH (3" OR 4") IN DROP-DOWN. CORRECT BOLT LENGTH WILL BE INCLUDED. INCLUDES: 1 x BOW STOP ROLLER * 2 x PQ1600 WHEEL 8" 1 x CAPSCREW PLATED 1/2 x * GR5 1 x NYLOCK NUT 1/2-13 PLATED 2 x WASHER FLAT 1/2 GALVANIZED

PS0867-1 ~ DUAL KAYAK CROSS-BUNK

REPRESENTATION PHOTO MAGIC TILT KAYAK CROSS BUNK BOLTS PERPENDICULAR TO A 2" x 3" CENTER SUPPORT. CAN HOLD ONE OR TWO KAYAKS. 6" CLEARANCE FROM TONGUE. INCLUDES: 2x4x6' CARPETED BUNK ON GALVANIZED SUPPORT 2 X UBOLTS - 1/2 x 2-1/16 x 4-5/16, GALV 4 X NUTS - 1/2, GALV 4 X LOCK WASHERS - 1/2, GALV 2 x WELDED TIE-DOWNS ON ENDS

PS1110 ~ TONGUE ROLLER BRACKET 5"

REPRESENTATION PHOTO MAGIC TILT TONGUE ROLL BRACKET ~ PS1110 SOLD INDIVIDUALLY

PS1540 ~ ROLLER BRACKET 12" (PONTOON / CAT)

REPRESENTATION PHOTO MAGIC TILT ROLLER BRACKET ~ PS1540 CAN BE USED FOR SPLIT-HULL VESSELS (PONTOONS, HOBIE CATS, CATAMARANS) THAT DON'T REQUIRE FULL-LENGTH SUPPORT MOUNTING HARDWARE NOT INCLUDED USES 2-1/2" STRAIGHT ROLLERS (NOT INCLUDED) REPLACEMENT BRACKET FOR PS1550 ASSEMBLY

PS1550 ~ ROLLER BRACKET ASSEMBLY 12" (PONTOON / CAT)

REPRESENTATION PHOTO MAGIC TILT ROLLER BRACKET ASSEMBLY ~ PS1550 CAN BE USED FOR SPLIT-HULL VESSELS (PONTOONS, HOBIE CATS, CATAMARANS) THAT DON'T REQUIRE FULL-LENGTH SUPPORT MOUNTING HARDWARE NOT INCLUDED USES PS1540 BRACKET USES 2-1/2" STRAIGHT ROLLERS

PS2655 ~ CA CHANNEL MOUNT GUIDE POLE MOUNT PLATE ALUMINUM

REPRESENTATION PHOTO MAGIC TILT MOUNT PLATE ~ PS2655 USED IN HARDWARE KIT PS2658 . FOR MOUNTING GUIDE POLES TO CA SERIES ALUMINUM TRAILERS EQUIPED WITH UNDER-FRAME CHANNEL.

PS2658 ~ CA CHANNEL MOUNT GUIDE POLE MOUNT KIT

REPRESENTATION PHOTO MAGIC TILT GUIDE POLE MOUNT ASSEMBLY ~ PS2658 CHANNEL. INCLUDES: 2 x PS2653-1 CLAMP-ON FOR 1-1/2" GUIDE POLES GALV 2 x PS2655 GUIDE PLATE FOR CA SERIES TRAILERS WITH UNDER-FRAME CHANNEL ALUM 4 x PY1701 1/2" x 1-1/2" SQUARE-HEAD BOLT STAINLESS 4 x PY1820 1/2" NYLOCK NUT STAINLESS 4 x PY1905 1/2" FLAT WASHER STAINLESS 8 x PY1710 3/8" x 1-1/4" BOLT STAINLESS 8 x PY1810 3/8" NYLOCK NUT STAINLESS 16 x PY1902 3/8" FLAT WASHER STAINLESS

PT0301-1 ~ T-BUNK ASSEMBLY 18"

REPRESENTATION PHOTO MAGIC TILT T-BUNK ASSEMBLY ~ PT0301-1 INCLUDES: 2 x PS1110 TONGUE ROLLER BRACKET 1 x PT0301 CARPETED T-BUNK (2"x6"x18") 2 x PT2070 PIVOT L-BRACKET, GALV 2 x PY1620 BOLT 3/8" x 4" GALV 2 x PY1650 BOLT 3/8" x 1-1/4" GALV 4 x PY1405 NUT 3/8" GALV 4 x PY1605 LOCK WASHER 3/8" GALV 4 x PY0409 LAG SCREW 3/8" x 1-1/4" PLATED USED ON SKIFFS AND JON BOATS IN PLACE OF A FRONT KEEL ROLLER MOUNTS TO TONGUE, NOT CROSSMEMBER CARPETTED BOARDS PIVOT TO ALIGN WITH HULL

PT1001 ~ VERTICAL CARPETED BUNK

2" x 4"

REPRESENTATION PHOTO MAGIC TILT CARPETED BUNK ~ PT1001 PLEASE CALL 941-358-1117 FOR ORDERING & SHIPPING PRICE. CARPETED BUNKS ARE SOLD PER FOOT AND CAN BE CUT TO ANY CUSTOM LENGTH DESIRED. AVAILABLE IN BLACK OR GRAY CARPETING . SPECIFY WHEN CALLING . THESE BUNKS ARE DESIGNED TO BE MOUNTED IN THE VERTICAL POSSITION WITH VERTICAL BUNK BRACKETS .

PT1520 ~ VERTICAL BUNK BRACKET YOKE 3"

REPRESENTATION PHOTO MAGIC TILT BUNK BRACKET YOKE ~ PT1520 USED WITH PT1001 VERTICAL 2" x 4" BUNKS BOLTS DIRECTLY TO FRAME OR CROSSMEMBER

PT1535 ~ BUNK BRACKET 4" PONTOON (KARAVAN 100-02456-GL)

REPRESENTATION PHOTO MAGIC TILT BUNK BRACKET ~ PT1535 LAG SCREWS AND U-BOLTS NOT INCLUDED

PT1610 ~ PERMALOCK BUNK BRACKET ADJUSTABLE 12"

REPRESENTATION PHOTO MAGIC TILT BUNK BRACKET ~ PT1610 PERMALOCK FEATURE HELPS LIMIT TILTING FROM SIDE LOADING FORCES FOR USE WITH (NOT INCLUDED): PT1612 PERMALOCK CLAMP 7/16" DIAMETER U-BOLTS PIVOT TOPS PT2075, PT2070, PT2050

PT1612 ~ PERMALOCK CLAMP 3"

REPRESENTATION PHOTO MAGIC TILT PERMALOCK CLAMP ~ PT1612 FOR USE WITH PT1610 PERMALOCK BUNK BRACKETS REQUIRES 1 x PY0308 5/16" x 3/4" PLATED CARRIAGE BOLT & 1 x PY1291 5/16" FLANGE NUT (NOT INCLUDED)

PT1630 ~ CLAMP-ON PIVOT-L BUNK BRACKET 2"

REPRESENTATION PHOTO MAGIC TILT CS CROSSMEMBER BUNK BRACKET ~ PT1630 USE WITH PIVOT-L BUNK BRACKETS (NOT INCLUDED) OFTEN USED FOR PONTOON AND CAT BUNK SUPPORT ALLOWS MOUNTING HORIZONTAL BUNKS CLOSER TO CROSSMEMBER

PT2018 ~ PONTOON WING BRACKET

REPRESENTATION PHOTO MAGIC TILT PONTOON WING BRACKET ~ PT2018 SLOTTED HOLES IN BRACKET ALLOW FOR ADJUSTMENT & STABILITY MULTIPLE MOUNTING HOLES IN WINGS ALLOW YOU TO USE LAG SCREWS OR FANG BOLTS TO SECURE HORIZONTAL BUNKS CAN ACCOMODATE 4", 6", 8" WIDE HORIZONTAL BUNK BOARDS

PT2025 ~ PONTOON WING BRACKET WITH YOKE

REPRESENTATION PHOTO MAGIC TILT PONTOON WING BRACKET ~ PT2025 HOLES IN WINGS ALLOW YOU TO USE LAG SCREWS OR FANG BOLTS TO SECURE HORIZONTAL BUNKS CAN ACCOMODATE 4", 6", 8" WIDE HORIZONTAL BUNK BOARDS

PT2060 ~ PIVOT "L" BRACKET W/ ROUND HOLES

REPRESENTATION PHOTO MAGIC TILT PIVOT "L" BRACKET ~ PT2060 (ROUND HOLES) HOLE SIZES: 3/8" TO WOOD BUNK 1/2" PIVOT HOLE SOLD INDIVIDUALLY LAG SCREWS AND PIVOT BOLTS NOT INCLUDED

PT2080 ~ SIDE GUIDE BRACKET CUSTOM

REPRESENTATION PHOTO MAGIC TILT SIDE-GUIDE CUSTOM BRACKET ~ PT2080

PT2160 ~ SIDE GUIDE BRACKET BOLT PLATE

REPRESENTATION PHOTO MAGIC TILT SIDE GUIDE BOLT PLATE ~ PT2160 USED WITH SIDE GUIDE BRACKETS

PT2190 ~ BOW BOARD HARDWARE KIT HEAVY DUTY ALUMINUM/STAINLESS

REPRESENTATION PHOTO MAGIC TILT BOW BOARD HARDWARE KIT ~ PT2190 DOES NOT INCLUDE LAG SCREWS TO FASTEN BOARDS INCLUDES: 4 X PS2653-A CLAMP-ON TOP HAT ALUMINUM 4 X PT1882 TUBE 2" x 2" x 12" WITH PIVOT HOLE ALUMINUM 4 X PT2075 PIVOT "L" BRACKET ALUMINUM 4 X PY1020 LOCK WASHER 3/8" STAINLESS 4 X PY1720 BOLT 3/8" x 3" STAINLESS 4 X PY1782 NUT 3/8" STAINLESS 8 X PY1902 FLAT WASHER 3/8" STAINLESS 8 X PY2540 U-BOLT 1/2" x 3-1/16" x 4-5/16" STAINLESS 16 X PY1025 LOCK WASHER 1/2" STAINLESS 16 X PY1785 NUT 1/2" STAINLESS

PT2200 ~ BOW BOARD KIT LIGHT-DUTY

6'

Magic Tilt Bow Board Kit ~ PT2200 Spans Two 3" x 3" Crossmembers at front of trailer. Can be used on other crossmember sizes by changing the u-bolts. Included in this kit: 4 x PT1565 8" Bunk Bracket Galv 2 x Carpeted Horizontal Bunk 2" x 6" x 6' 4 x PT2070 Pivot L-Bracket Galv 8 x PY0411 3/8 x 1-1/4" Lag Screw Galv 4 x PY1405 3/8 Hex Nut Galv 8 x PY1406 7/16 Hex Nut Galv 4 x PY1505 3/8 Flat Washer Galv 4 x PY1605 3/8 Lock Washer Galv 8 x PY1606 7/16 Lock Washer Galv 4 x PY1650 3/8 x 1-1/4" Bolt Galv 4 x PY2096 7/16 x 3-1/16" x 4-5/16" U-Bolt Galv

PT2205 ~ CROSSMEMBER BUNK "L" BRACKET LOW PROFILE GALVANIZED

REPRESENTATION PHOTO MAGIC TILT CROSSMEMBER BUNK "L" BRACKET SOLD INDIVIDUALLY ORIGINALLY USED TO SUPPORT ROLLER TRAILER PIVOT ASSEMBLIES. CAN BE USED TO SECURE VERTICAL BUNKS RESTING DIRECTLY ON CROSSMEMBERS. NOT RECOMMENDED FOR VERTICAL BUNKS OVER 6” TALL REQUIRES ONE 1/2" U-BOLT TO MOUNT TO CROSS MEMBER AND ONE 1/2" THRU-BUNK BOLTS (NOT INCLUDED)

PU4025 ~ TUBE BUNK BRACKET MATERIAL 1-1/2" GALVANIZED BULK

REPRESENTATION PHOTO MAGIC TILT TUBE BUNK BRACKET MATERIAL~ PU4025 (PLEASE CALL 941-358-1117 FOR SHIPPING QUOTE) PRE-CUT TUBES WITH PIVOT HOLES AVAILABLE HERE NO DRILLED HOLES CUT ENDS WILL NOT BE GALVANIZED

PV1930 ~ GALVANIZED TRAILER UNIVERSAL GUIDE POLE MOUNT KIT

REPRESENTATION PHOTO MAGIC TILT GUIDE-ON ASSEMBLY ~ PV1930 TO ORDER, SELECT FRAME HEIGHT IN DROP-DOWN INCLUDES: 2 x PV1925 UNIVERSAL GUIDE-ON BRACKET 4 x PY1995 U-BOLT 3/8" 1-9/16 x 2-5/8 GALV 4 x U-BOLT 1/2" 2-1/16 x * (SELECT FRAME HEIGHT IN DROP-DOWN) 8 x PY1405 3/8" NUT GALV 8 x PY1605 3/8" LOCK WASHER GALV 8 x PY1410 1/2" NUT GALV 8 x PY1610 1/2" LOCK WASHER GALV 8 x PY1515 1/2" FLAT WASHER GALV

Roll Brackets

TANDEM ROLL BRKT.-12"

Rub Pads

2 sizes available

Side Guide Assemblies

3 sizes available

Step Pads With Boots

39 sizes available

Step Pads without Boots

18 sizes available

Boot sold separately