Search Results

90885 ~ TEKONSHA P2 ELECTRIC BRAKE CONTROLLER

REPRESENTATION PHOTO ** THIS IS A SPECIAL BUY OFFERED AT A GREATLY REDUCE PRICE! ** MAGIC TILT ELECTRIC BRAKE CONTOLLER ~ 90885 The Prodigy P2 electric brake controller supplies power to your tow vehicle's brakes proportionally. This means that your trailer brakes at the same time and with the same strength as your vehicle - even in reverse gear. If you have to slam on your truck's brakes, the trailer's brakes respond instantly, too - there's no delay. Therefore your vehicle's brakes aren't overworked from trying to stop the entire load, and they suffer less wear and tear extending the longevity of your brakes compared to time based controls. The P2 also cuts power to the trailer's brakes when your vehicle is stopped - extending the life of the magnets and brake shoes in the trailer's brake assemblies. Aside from smoother, more efficient braking that results from proportional application of stopping power, the Prodigy P2 also has a boost feature that gives you more initial braking power for those times when you're towing heavier loads. That's when more braking power is needed to stop the trailer at the same time as the tow vehicle. The boost setting sends 13 or 25 percent more power (depending on which setting you choose) back to the trailer brakes, thus compensating for heavier loads. You can boost the power manually at the push of a button as well. The boost feature gets more power to the trailer brakes exactly when you need it most, and your fully loaded rig brakes smoothly and comfortably. This brake controller levels automatically as you drive, so there's no problem using it on steep hills or when towing through the mountains. The self-leveling feature also makes the Prodigy easy to install: Simply mount it in your cab at any vertical angle (it has 360-degree rotation). It's easy to see the display and to access the pivoting manual override lever on the bottom of the unit. The P2's continuous diagnostic check monitors your connection and magnet condition, so you can fix any problems before they land you on the side of the road. This newest version of Tekonsha's popular Prodigy brake controller has reverse battery protection to preserve the unit and accessory systems. And the power-save mode reduces battery drain when the controller isn't in use.

Brake Line Kits for Single Axle

6 sizes available

1- HYD. BRAKE HOSE W/SWIVEL 19' 1- HYD.BRAKE/BRASS T-FITTING 1- HYD. BRAKE HOSE W/SWIVEL 1' 1- HYD. BRAKE HOSE W/SWIVEL 6'6" 10 - PLASTIC WIRE TIE HD 14-1/2""

HYDRAULIC RUBBER BRAKE HOSES

15 sizes available

PG1030 COMPLETE 5-LUG DISC BRAKE KIT ≤7.5K TOP-MOUNT (DEXTER / UFP)

REPRESENTATION PHOTO IF YOU WANT TO ADD BRAKES TO A TRAILER THAT WAS NEVER EQUIPPED WITH THEM, MAKE SURE THERE IS AT LEAST FOUR-INCHES OF CLEARANCE FROM THE BRAKE MOUNTING PLATE ON THE AXLE OR TORSION ARM TO THE OUTSIDE EDGE OF THE FRAME. MAGIC TILT BRAKE KIT ~ PG1030 NEW TOP-MOUNT ACTUATOR REPLACES THE PG1088 INLINE 3-HOLE ACTUATOR ON 3" TALL TONGUES. NEW HOLES WILL NEED TO BE DRILLED IN THE TRAILER TONGUE. COMES WITH PG4856 DOUBLE BANJO FITTING TO CONNECT BRAKE LINES. UFP SPINDLE MOUNTING HARDWARE (NOT INCLUDED): PH2125 IF USING ON NON-UFP AXLES WITH 1" SPINDLE THREADS YOU WILL NEED THE PH2160 CONVERSION KIT (NOT INCLUDED). ADDITIONAL AXLE(S) BRAKE KIT PG1040 (NOT INCLUDED) INCLUDES: 2 x BEARING 1-1/16" (44649) 2 x BEARING 1-3/8" (68149) 2 x SEAL 1-3/8" UFP (257-168) 1 x BEARING PROTECTOR SET SS 1.980 1 x PG1072 ACTUATOR TOP MOUNT DISC DEMCO #7,000 1 x HYDRAULIC BRAKE HOSE W/ SWIVEL 8' 1 x HYDRAULIC BRAKE HOSE W/ SWIVEL 23' 2 x PG2026-1 DISC ROTOR AND HUB 10" 5-LUG UFP 1 x CALIPER FITTING PLUG UFP #32212 1 x PG5003 DISC BRAKE CALIPER ASSEMBLY LH UFP DB3 (DOUBLE BANJO FITTING) 1 x PG5005 DISC BRAKE CALIPER ASSEMBLY RH UFP DB3 (DOUBLE BANJO FITTING) 4 x 7/16" x 1" SHCS BOLT UFP DISC CALIPER 1 x PL2128 5-WAY FULL GROUND WIRE HARNESS 30' 6 x PLASTIC WIRE TIE HD 14-1/2" 2 x 1/4" CHAIN W/ ONE HOOK 40" 3 x CAPSCREW PLATED NC 1/2 x 4-1/2 GR5 3 x NUT LOCK NI 1/2-13 PLATED OWNERS MANUAL

PG1031 COMPLETE 5-LUG DISC BRAKE KIT ≤7.5K IN-LINE (DEXTER / UFP)

REPRESENTATION PHOTO IF YOU WANT TO ADD BRAKES TO A TRAILER THAT WAS NEVER EQUIPPED WITH THEM, MAKE SURE THERE IS AT LEAST FOUR-INCHES OF CLEARANCE FROM THE BRAKE MOUNTING PLATE ON THE AXLE OR TORSION ARM TO THE OUTSIDE EDGE OF THE FRAME. MAGIC TILT BRAKE KIT ~ PG1031 COMES WITH PG4856 DOUBLE BANJO FITTING TO CONNECT BRAKE LINES. IF USING ON NON-UFP AXLES WITH 1" SPINDLE THREADS YOU WILL NEED THE PH2160 CONVERSION KIT (NOT INCLUDED) UFP SPINDLE MOUNTING HARDWARE (NOT INCLUDED): PH2125 ADDITIONAL AXLE(S) BRAKE KIT PG1040 (NOT INCLUDED) INCLUDES: 2 x BEARING 1-1/16" (44649) 2 x BEARING 1-3/8" (68149) 2 x SEAL 1-3/8" UFP (257-168) 1 x BEARING PROTECTOR SET SS 1.980 1 x PG1090 ACTUATOR IN-LINE DISC UFP #7500 1 x HYDRAULIC BRAKE HOSE W/ SWIVEL 8' 1 x HYDRAULIC BRAKE HOSE W/ SWIVEL 23' 2 x PG2026-1 DISC ROTOR AND HUB 10" 5-LUG UFP 1 x CALIPER FITTING PLUG UFP #32212 1 x PG5003 DISC BRAKE CALIPER ASSEMBLY LH UFP DB3 (DOUBLE BANJO FITTING) 1 x PG5005 DISC BRAKE CALIPER ASSEMBLY RH UFP DB3 (DOUBLE BANJO FITTING) 4 x 7/16" x 1" SHCS BOLT UFP DISC CALIPER 1 x PL2128 5-WAY FULL GROUND WIRE HARNESS 30' 6 x PLASTIC WIRE TIE HD 14-1/2" 2 x 1/4" CHAIN W/ ONE HOOK 40" 4 x CAPSCREW PLATED NC 1/2 x 4-1/2 GR5 4 x NUT LOCK NI 1/2-13 PLATED OWNERS MANUAL

PG1033 COMPLETE 5-LUG DISC BRAKE KIT 7.5K TO 16K (DEXTER / UFP)

REPRESENTATION PHOTO IF YOU WANT TO ADD BRAKES TO A TRAILER THAT WAS NEVER EQUIPPED WITH THEM, MAKE SURE THERE IS AT LEAST FOUR-INCHES OF CLEARANCE FROM THE BRAKE MOUNTING PLATE ON THE AXLE OR TORSION ARM TO THE OUTSIDE EDGE OF THE FRAME. MAGIC TILT BRAKE KIT ~ PG1033 COMES WITH PG4856 DOUBLE BANJO FITTING TO CONNECT BRAKE LINES. UFP SPINDLE MOUNTING HARDWARE (NOT INCLUDED): PH2125 IF USING ON NON-UFP AXLES WITH 1" SPINDLE THREADS YOU WILL NEED THE PH2160 CONVERSION KIT (NOT INCLUDED) ADDITIONAL AXLE(S) BRAKE KIT PG1040 (NOT INCLUDED) INCLUDES: 2 x BEARING 1-1/16" (44649) 2 x BEARING 1-3/8" (68149) 2 x SEAL 1-3/8" UFP (257-168) 2 x BEARING PROTECTOR 1.980 STAINLESS 1 x PG1095 ACTUATOR IN-LINE DISC #16,000 1 x HYDRAULIC BRAKE HOSE W/ SWIVEL 8' 1 x HYDRAULIC BRAKE HOSE W/ SWIVEL 23' 2 x PG2026-1 DISC ROTOR AND HUB 10" 5-LUG UFP 1 x CALIPER FITTING PLUG UFP #32212 1 x PG5003 DISC BRAKE CALIPER ASSEMBLY LH UFP (DOUBLE BANJO FITTING) 1 x PG5005 DISC BRAKE CALIPER ASSEMBLY RH UFP (DOUBLE BANJO FITTING) 4 x 7/16" x 1" CALIPER BOLT UFP 1 x PL2128 5-WAY HARNESS 30' 6 x PLASTIC WIRE TIE HD 14-1/2" 2 x 1/4" CHAIN W/ ONE HOOK 40" 4 x CAPSCREW PLATED NC 1/2 x 4-1/2 GR5 4 x NUT LOCK NI 1/2-13 PLATED OWNERS MANUAL

PG1037 COMPLETE 6-LUG DISC BRAKE KIT 10K TO 16K (DEXTER / UFP)

REPRESENTATION PHOTO IF YOU WANT TO ADD BRAKES TO A TRAILER THAT WAS NEVER EQUIPPED WITH THEM, MAKE SURE THERE IS AT LEAST FOUR-INCHES OF CLEARANCE FROM THE BRAKE MOUNTING PLATE ON THE AXLE OR TORSION ARM TO THE OUTSIDE EDGE OF THE FRAME. MAGIC TILT BRAKE KIT ~ PG1037 COMES WITH PG4856 DOUBLE BANJO FITTING TO CONNECT BRAKE LINES. UFP SPINDLE MOUNTING HARDWARE (NOT INCLUDED): PH2130 IF USING ON NON-UFP AXLES WITH 1" SPINDLE THREADS YOU WILL NEED THE PH2165 CONVERSION KIT (NOT INCLUDED) ADDITIONAL AXLE(S) BRAKE KIT PG1042 (NOT INCLUDED) INCLUDES: 2 x BEARING 1-1/4" UFP 2 x BEARING 1-3/4" UFP (25580) 2 x SEAL 1-3/4" UFP (21333) 2 x PF1101 STAINLESS BEARING PROTECTOR 2.441" 1 x PG1095 ACTUATOR DISC UFP #16,000 1 x HYDRAULIC BRAKE HOSE W/ SWIVEL 8' 1 x HYDRAULIC BRAKE HOSE W/ SWIVEL 23' 2 x PG2027-1 DISC ROTOR AND HUB 12" 6-LUG UFP 1 x CALIPER FITTING PLUG UFP #32212 1 x PG5003 DISC BRAKE CALIPER ASSEMBLY LH UFP DB3 (DOUBLE BANJO FITTING) 1 x PG5005 DISC BRAKE CALIPER ASSEMBLY RH UFP DB3 (DOUBLE BANJO FITTING) 4 x DISC CALIPER BOLT 7/16" x 1" SHCS (UFP) 1 x PL2128 5-WAY FULL GROUND WIRE HARNESS 30' 6 x PLASTIC WIRE TIE HD 14-1/2" 2 x CHAIN W/ ONE HOOK 40" 4 x CAPSCREW PLATED NC 1/2" x 4-1/2" GR5 4 x NUT LOCK NI 1/2-13 PLATED OWNERS MANUAL

PG1038 COMPLETE 8-LUG DISC BRAKE KIT 12K TO 20K (DEXTER / UFP)

REPRESENTATION PHOTO IF YOU WANT TO ADD BRAKES TO A TRAILER THAT WAS NEVER EQUIPPED WITH THEM, MAKE SURE THERE IS AT LEAST FOUR-INCHES OF CLEARANCE FROM THE BRAKE MOUNTING PLATE ON THE AXLE OR TORSION ARM TO THE OUTSIDE EDGE OF THE FRAME. MAGIC TILT BRAKE KIT ~ PG1038 TANDEM 8,000-POUND (8-LUG) AXLE TRAILERS COMES WITH PG4856 DOUBLE BANJO FITTING TO CONNECT BRAKE LINES. UFP SPINDLE MOUNTING HARDWARE (NOT INCLUDED): PH2130 IF USING ON NON-UFP AXLES WITH 1" SPINDLE THREADS YOU WILL NEED THE PH2165 CONVERSION KIT (NOT INCLUDED) ADDITIONAL AXLE(S) BRAKE KIT PG1044 (NOT INCLUDED) INCLUDES: 2 x BEARING 1-1/4" UFP 2 x BEARING 1-3/4" UFP (25580) 2 x SEAL 1-3/4" UFP (21333) 1 x BEARING PROTECTOR SET SS 2.717 1 x PG1096 DEMCO ACTUATOR DISC #20000 1 x HYDRAULIC BRAKE HOSE W/ SWIVEL 8' 1 x HYDRAULIC BRAKE HOSE W/ SWIVEL 23' 2 x PG2028-1 DISC ROTOR AND HUB 12" 8-LUG UFP 1 x CALIPER FITTING PLUG UFP #32212 1 x PL2142 5-WAY FULL GROUND WIRE HARNESS 40' 1 x PG5003 DISC BRAKE CALIPER ASSEMBLY LH UFP DB3 (DOUBLE BANJO FITTING) 1 x PG5005 DISC BRAKE CALIPER ASSEMBLY RH UFP DB3 (DOUBLE BANJO FITTING) 4 x DISC CALIPER BOLT 7/16" x 1" SHCS (UFP) 6 x PLASTIC WIRE TIE HD 14-1/2" 2 x CHAIN W/ ONE HOOK 40" 4 x CAPSCREW PLATED NC 1/2" x 4-1/2" GR5 4 x NUT LOCK NI 1/2-13 PLATED OWNERS MANUAL

PG1040 ADDITIONAL AXLE 5-LUG DISC BRAKE KIT (DEXTER / UFP)

REPRESENTATION PHOTO IF YOU WANT TO ADD BRAKES TO A TRAILER THAT WAS NEVER EQUIPPED WITH THEM, MAKE SURE THERE IS AT LEAST FOUR-INCHES OF CLEARANCE FROM THE BRAKE MOUNTING PLATE ON THE AXLE OR TORSION ARM TO THE OUTSIDE EDGE OF THE FRAME. MAGIC TILT BRAKE KIT ~ PG1040 COMES WITH PG4856 DOUBLE BANJO FITTING TO CONNECT BRAKE LINES. UFP SPINDLE MOUNTING HARDWARE (NOT INCLUDED): PH2125 IF USING ON NON-UFP AXLES WITH 1" SPINDLE THREADS YOU WILL NEED THE PH2160 CONVERSION KIT (NOT INCLUDED) INCLUDES: 2 x BEARING 1-1/16" (44649) 2 x BEARING 1-3/8" (68149) 2 x SEAL 1-3/8" UFP (257-168) 1 x BEARING PROTECTOR SET SS 1.980 1 x HYDRAULIC BRAKE HOSE W/ SWIVEL 4' 1 x HYDRAULIC BRAKE HOSE W/ SWIVEL 8' 2 x PG2026-1 DISC ROTER AND HUB 10" 5-LUG UFP 1 x CALIPER FITTING PLUG UFP #32212 1 x PG5003 DISC BRAKE CALIPER ASSEMBLY LH UFP DB3 (DOUBLE BANJO FITTING) 1 x PG5005 DISC BRAKE CALIPER ASSEMBLY RH UFP DB3 (DOUBLE BANJO FITTING) 4 x DISC CALIPER BOLT 7/16" x 1" SHCS (UFP) 6 x PLASTIC WIRE TIE HD 14-1/2" OWNERS MANUAL

PG1042 ADDITIONAL AXLE 6-LUG DISC BRAKE KIT (DEXTER / UFP)

REPRESENTATION PHOTO IF YOU WANT TO ADD BRAKES TO A TRAILER THAT WAS NEVER EQUIPPED WITH THEM, MAKE SURE THERE IS AT LEAST FOUR-INCHES OF CLEARANCE FROM THE BRAKE MOUNTING PLATE ON THE AXLE OR TORSION ARM TO THE OUTSIDE EDGE OF THE FRAME. MAGIC TILT BRAKE KIT ~ PG1042 COMES WITH PG4856 DOUBLE BANJO FITTING TO CONNECT BRAKE LINES. UFP SPINDLE MOUNTING HARDWARE (NOT INCLUDED): PH2130 IF USING ON NON-UFP AXLES WITH 1" SPINDLE THREADS YOU WILL NEED THE PH2165 CONVERSION KIT (NOT INCLUDED) INCLUDES: 2 x BEARING 1-1/4" 2 x BEARING 1-3/4" (25580) 2 x SEAL 1-3/4" UFP (21333) 2 x PF1101 STAINLESS BEARING PROTECTOR 2.441" 1 x HYDRAULIC BRAKE HOSE W/ SWIVEL 4' 1 x HYDRAULIC BRAKE HOSE W/ SWIVEL 8' 2 x PG2027-1 DISC ROTER AND HUB 12" 6-LUG UFP 1 x CALIPER FITTING PLUG UFP #32212 1 x PG5003 DISC BRAKE CALIPER ASSEMBLY LH UFP DB3 (DOUBLE BANJO FITTING) 1 x PG5005 DISC BRAKE CALIPER ASSEMBLY RH UFP DB3 (DOUBLE BANJO FITTING) 4 x DISC CALIPER BOLT 7/16" x 1" SHCS (UFP) 6 x PLASTIC WIRE TIE HD 14-1/2" OWNERS MANUAL

PG1044 ADDITIONAL AXLE 8-LUG DISC BRAKE KIT (DEXTER / UFP)

REPRESENTATION PHOTO IF YOU WANT TO ADD BRAKES TO A TRAILER THAT WAS NEVER EQUIPPED WITH THEM, MAKE SURE THERE IS AT LEAST FOUR-INCHES OF CLEARANCE FROM THE BRAKE MOUNTING PLATE ON THE AXLE OR TORSION ARM TO THE OUTSIDE EDGE OF THE FRAME. MAGIC TILT BRAKE KIT ~ PG1044 COMES WITH PG4856 DOUBLE BANJO FITTING TO CONNECT BRAKE LINES. UFP SPINDLE MOUNTING HARDWARE (NOT INCLUDED): PH2130 IF USING ON NON-UFP AXLES WITH 1" SPINDLE THREADS YOU WILL NEED THE PH2165 CONVERSION KIT (NOT INCLUDED) INCLUDES: 2 x BEARING 1-1/4" 2 x BEARING 1-3/4" (25580) 2 x SEAL 1-3/4" UFP (21333) 2 x BEARING PROTECTOR 2.328 1 x HYDRAULIC BRAKE HOSE W/ SWIVEL 4' 1 x HYDRAULIC BRAKE HOSE W/ SWIVEL 8' 1 x PG2028-1 DISC ROTER AND HUB 12" 8-LUG UFP 2 x CALIPER FITTING PLUG UFP #32212 1 x PG5003 DISC BRAKE CALIPER ASSEMBLY LH UFP DB3 (DOUBLE BANJO FITTING) 1 x PG5005 DISC BRAKE CALIPER ASSEMBLY RH UFP DB3 (DOUBLE BANJO FITTING) 4 x DISC CALIPER BOLT 7/16" x 1" SHCS (UFP) 6 x PLASTIC WIRE TIE HD 14-1/2" OWNERS MANUAL

PG1166 ~ BRAKE LINE COUPLER

REPRESENTATION PHOTO MAGIC TILT BRAKE LINE COUPLER ~ PG1166

PG1175 ~ HYDRAULIC BRAKE T-FITTING

REPRESENTATION PHOTO MAGIC TILT HYDRAULIC BRAKE T-FITTING ~ PG1175

PG1332 ~ BRAKE LINE KIT TO ADD SECOND AXLE SINGLE-BANJO

REPRESENTATION PHOTO MAGIC TILT BRAKE LINE KIT SECOND AXLE ~ PG1332 INCLUDES: 2 x PG1175 T-FITTINGS 2 x PG1178 1' BRAKE HOSE WITH SWIVEL 1 x PG1182 4' BRAKE HOSE WITH SWIVEL 1 x PG1183 6' 6" BRAKE HOSE WITH SWIVEL 6 x PL2954 14-1/2" PLASTIC WIRE TIES

PG1332-1 ~ BRAKE LINE KIT TO ADD SECOND AXLE DOUBLE-BANJO

REPRESENTATION PHOTO MAGIC TILT BRAKE LINE KIT SECOND AXLE ~ PG1332-1 INCLUDES: 1 x PG4862 BRAKE CALIPER FITTING PLUG 1 x PG1182 4' BRAKE HOSE WITH SWIVEL 1 x PG1186 8' BRAKE HOSE WITH SWIVEL 6 x PL2954 14" PLASTIC WIRE TIES

PG1334 ~ BRAKE LINE KIT TO ADD SECOND & THIRD AXLES SINGLE-BANJO

REPRESENTATION PHOTO MAGIC TILT BRAKE LINE KIT SECOND & THIRD AXLE ~ PG1334 INCLUDES: 4 x PG1175 T-FITTING 3 x PG1178 1' BRAKE HOSE WITH SWIVEL 2 x PG1182 4' BRAKE HOSE WITH SWIVEL 2 x PG1183 6' 6" BRAKE HOSE WITH SWIVEL 12 x PL2954 14" PLASTIC WIRE TIE

PG1334-1 ~ BRAKE LINE KIT TO ADD SECOND & THIRD AXLES DBL-BANJO

REPRESENTATION PHOTO MAGIC TILT BRAKE LINE KIT SECOND & THIRD AXLE ~ PG1334-1 INCLUDES: 1 x PG4862 CALIPER FIITING PLUG 2 x PG1182 4' BRAKE HOSE WITH SWIVEL 2 x PG1186 8' BRAKE HOSE WITH SWIVEL 12 x PL2954 14" PLASTIC WIRE TIE

PG2252 ~ REVERSE LOCKOUT SOLENOID

REPRESENTATION PHOTO MAGIC TILT REVERSE LOCKOUT SOLENOID ~ PG2252 CAN BE USED WHEN CONVERTING A DRUM ACTUATOR FOR DISC BRAKE USE. MAY SHIP FROM STORE LOCATION

PG4815-1 ~ SOLENOID ASSEMBLY DEXTER / UFP (054-140-22)

REPRESENTATION PHOTO MAGIC TILT SOLENOID ASSEMBLY ~ PG4815-1 THIS IS THE NEW-STYLE SOLENOID WITH TWO WIRES AND WITHOUT A BYPASS HOSE AND WILL ONLY WORK ON THE NEW-STYLE UFP MASTER CYLINDER PG4814-1 . IT WILL NOT WORK ON THE OLD-STYLE UFP MASTER CYLINDERS THAT REQUIRE A BYPASS HOSE.