Keel Rollers & Assemblies

10" Keel Rolls

2 sizes available

12" Keel Rolls

3 sizes available

5/8" Shafts

3 sizes available

Airboat Guide Poles

2 sizes available

Bow Stop Rollers

8 sizes available

Clamp-On Sockets

3 sizes available

Width4"

End Caps Bell

11 sizes available

KEEL ROLL BRACKET ASSY

2 sizes available

SKUPS1310-1

Plastic Bunk Cover

4 sizes available

PP2245 ~ RUB STRIP WITH HOLES 4" x 10" x 3/8"

REPRESENTATION PHOTO MAGIC TILT RUB STRIP ~ PP2245 INCLUDES 4 SELF TAPPING MOUNTING SCREWS REPLACEMENT CENTER PAD FOR PV2280-3 ASSEMBLY PRE-DRILLED HOLE PATTERN NOT GUARANTEED TO MATCH OLDER HOLE PATTERN SOAK STRIP IN HOT WATER PRIOR TO INSTALLATION

PP2258 ~ BUNK SLIDE 3/8" x 12" x 8'

REPRESENTATION PHOTO MAGIC TILT BUNK SLIDE ~ PP2258 (PLEASE CALL 941-358-1117 FOR SHIPPING QUOTE AND TO ORDER) PREMOLDED WITH VEE DOWN CENTER NO HOLES MOUNTING HARDWARE NOT INCLUDED

PP2260 ~ RUB STRIP 3 x 2

REPRESENTATION PHOTO MAGIC TILT RUB STRIP ~ PP2260 MOUNTING HARDWARE NOT INCLUDED MOUNTED WITH RIVETS FROM FACTORY CAN BE MOUNTED WITH TWO PY0491 SCREWS

PP2270 ~ RUB STRIP 1-3/4 x 15

REPRESENTATION PHOTO MAGIC TILT RUB STRIP ~ PP2270 CAN BE TRIMMED TO DESIRED LENGTH MOUNTING HARDWARE NOT INCLUDED MOUNTED WITH RIVETS FROM FACTORY CAN BE MOUNTED WITH THREE PY0491 SCREWS

PQ1255 ~ KEEL ROLLER 12 in (SELF CENTERING)

REPRESENTATION PHOTO MAGIC TILT KEEL ROLLER ~ PQ1255 DESIGNED TO MAKE CENTERING YOUR BOAT MUCH EASIER WITH EMBEDDED GROOVES THAT CENTER THE BOAT AS IT ROLLS FORWARD. MADE OF EXTREMELY CUT AND WEAR-RESISTANT POLYURETHANE WITH AN ADDED UV INHIBITOR AND WILL NOT DEVELOP FLAT SPOTS OR MARK YOUR BOAT. KEEL ROLLERS ARE NOT INTENDED AS WEIGHT-BEARING STRUCTURES BUT AS A GUIDE AND PROTECTIVE DEVICE. WHEN PROPERLY ADJUSTED, THE KEEL SHOULD JUST TOUCH OR JUST CLEAR THE ROLLER. USE WITH PR1550 ROLLER SHAFT, OR PR1560 SHAFT AND TWO PQ1360 END CAPS (NOT INCLUDED)

PQ1600 ~ ROLLER END CAP WHEEL 8-1/2" (STOLTZ)

REPRESENTATION PHOTO MAGIC TILT END CAP WHEEL ~ PQ1600 SOLD INDIVIDUALLY OFTEN USED ON SKIFFS OR ANY BOW WITH A LARGE PROTRUSION WHERE ADDITIONAL STANDOFF IS REQUIRED.

PQ1650 ~ BOW STOP ROLLER ASSEMBLY 8"

REPRESENTATION PHOTO MAGIC TILT ROLLER ASSEMBLY ~ PQ1650 * SELECT INNER ROLLER LENGTH (3" OR 4") IN DROP-DOWN. CORRECT BOLT LENGTH WILL BE INCLUDED. INCLUDES: 1 x BOW STOP ROLLER * 2 x PQ1600 WHEEL 8" 1 x CAPSCREW PLATED 1/2 x * GR5 1 x NYLOCK NUT 1/2-13 PLATED 2 x WASHER FLAT 1/2 GALVANIZED

PR1650 ~ ROLLER SHAFT CAP NUT 5/8"

REPRESENTATION PHOTO MAGIC TILT ROLLER SHAFT CAP NUT ~ PR1650 SOLD INDIVIDUALLY USED WITH VARIOUS KEEL ROLLER MOUNTS AND 5/8" ROLLER SHAFTS

PS1010 ~ KEEL ROLLER ASSEMBLY 5"

REPRESENTATION PHOTO MAGIC TILT ROLLER ASSEMBLY ~ PS1010 KEEL ROLLERS ARE NOT INTENDED AS WEIGHT-BEARING STRUCTURES BUT AS A GUIDE AND PROTECTIVE DEVICE. WHEN PROPERLY ADJUSTED, THE KEEL SHOULD JUST TOUCH OR JUST CLEAR THE ROLLER. MOUNTING HARDWARE NOT INCLUDED

PS1110 ~ TONGUE ROLLER BRACKET 5"

REPRESENTATION PHOTO MAGIC TILT TONGUE ROLL BRACKET ~ PS1110 SOLD INDIVIDUALLY

PS1178 ~ TONGUE ROLLER ASSEMBLY 5" (KARAVAN 310-00324)

REPRESENTATION PHOTO MAGIC TILT TONGUE ROLLER ASSEMBLY ~ PS1178 INCLUDES: MOUNTING HARDWARE USES 2 X PS1110 BRACKETS MAY SHIP WITH BLUE OR BLACK ROLLER KEEL ROLLERS ARE NOT INTENDED AS WEIGHT-BEARING STRUCTURES BUT AS A GUIDE AND PROTECTIVE DEVICE. WHEN PROPERLY ADJUSTED, THE KEEL SHOULD JUST TOUCH OR JUST CLEAR THE ROLLER.

PS1280 ~ KEEL ROLLER BRACKET ASSEMBLY 8"

REPRESENTATION PHOTO MAGIC TILT ROLLER ASSEMBLY ~ PS1280 MOUNTING HARDWARE NOT INCLUDED NOT ADJUSTABLE

PS1540 ~ ROLLER BRACKET 12" (PONTOON / CAT)

REPRESENTATION PHOTO MAGIC TILT ROLLER BRACKET ~ PS1540 CAN BE USED FOR SPLIT-HULL VESSELS (PONTOONS, HOBIE CATS, CATAMARANS) THAT DON'T REQUIRE FULL-LENGTH SUPPORT MOUNTING HARDWARE NOT INCLUDED USES 2-1/2" STRAIGHT ROLLERS (NOT INCLUDED) REPLACEMENT BRACKET FOR PS1550 ASSEMBLY

PS1550 ~ ROLLER BRACKET ASSEMBLY 12" (PONTOON / CAT)

REPRESENTATION PHOTO MAGIC TILT ROLLER BRACKET ASSEMBLY ~ PS1550 CAN BE USED FOR SPLIT-HULL VESSELS (PONTOONS, HOBIE CATS, CATAMARANS) THAT DON'T REQUIRE FULL-LENGTH SUPPORT MOUNTING HARDWARE NOT INCLUDED USES PS1540 BRACKET USES 2-1/2" STRAIGHT ROLLERS

PS2150 ~ SET SCREW WITH NUT 7/16" x 1-1/2"

REPRESENTATION PHOTO MAGIC TILT SET SCREW ~ PS2150 REPLACEMENT SET SCREW FOR PS2640 ASSEMBLY USED WITH THE PS2649 , PS2310 & PS2401 CLAMP-ON SOCKETS AND PS2210 NUT RETAINER (NOT INCLUDED)

PS2210 ~ NUT RETAINER PLATE

REPRESENTATION PHOTO MAGIC TILT NUT RETAINER PLATE ~ PS2210 REPLACEMENT RETAINER FOR PS2640 ASSEMBLY USED WITH THE PS2649 AND PS2310 & PS2401 CLAMP-ON SOCKETS AND PS2150 SET SCREW (NOT INCLUDED)

PS2640 ~ CLAMP-ON ASSEMBLY 3" x 1-1/2" TUBE

REPRESENTATION PHOTO MAGIC TILT CLAMP-ON ASSEMBLY ~ PS2640 DESIGNED TO MOUNT HORIZONTAL BUNKS TO 3" x 3" CROSSMEMBERS INCLUDES: 1 x PS2150 SET SCREW W/ NUT PLATED 1 x PS2210 NUT RETAINER PLATE GALV 1 x PS2649 3" x 3" CLAMP-ON SOCKET GALV 1 x PT1760 BUNK RISER 1-1/2" x 1-1/2" x 12" SQUARE GALV 1 x PT2070 PIVOT L BRACKET GALV 2 x PY0409 LAG SCREW 3/8" x 1-1/4" PLATED 3 x PY1405 HEX NUT 3/8-16 GALV 3 x PY1505 FLAT WASHER 3/8" GALV 3 x PY1605 LOCK WASHER 3/8" GALV 1 x PY1615 BOLT 3/8" x 2-1/2" GALV 2 x PY1624 BOLT 3/8" x 4-1/2" GALV

PS2649 ~ CLAMP-ON SOCKET 3" x 1-1/2" TUBE

REPRESENTATION PHOTO MAGIC TILT CLAMP-ON SOCKET ~ PS2649 DESIGNED TO MOUNT HORIZONTAL BUNKS TO 3" x 3" CROSSMEMBERS REPLACEMENT SOCKET FOR THE PS2640 ASSEMBLY MOUNTS OVER CROSSMEMBER WITH 3/8" x 4-1/2" GALVANIZED BOLT (NOT INCLUDED) REQUIRES ONE EACH PS2210 NUT RETAINER AND PS2150 SET SCREW (NOT INCLUDED) USE WITH PRE-CUT 1-1/2" TUBE BRACKETS OR BULK TUBE BRACKETS (NOT INCLUDED)

PS2652 ~ CLAMP-ON SOCKET 3" x 2" TUBE

REPRESENTATION PHOTO MAGIC TILT CLAMP-ON SOCKET ~ PS2652 USED TO MOUNT ANY BOW REST OR BUNK GUIDE USING 2" x 2" VERTICAL TUBING REQUIRES TWO PS2150 SET SCREWS (NOT INCLUDED) MOUNTS TO 3" x 3" CROSSMEMBERS WITH TWO 3/8" x 4-1/2" GALVANIZED BOLTS (NOT INCLUDED) USE WITH PU4040 2" TUBE (NOT INCLUDED)

PS2653-1 ~ CLAMP-ON TOP HAT 1-1/2" GALVANIZED

REPRESENTATION PHOTO MAGIC TILT CLAMP-ON SOCKET ~ PS2653-1

PS2655 ~ CA CHANNEL MOUNT GUIDE POLE MOUNT PLATE ALUMINUM

REPRESENTATION PHOTO MAGIC TILT MOUNT PLATE ~ PS2655 USED IN HARDWARE KIT PS2658 . FOR MOUNTING GUIDE POLES TO CA SERIES ALUMINUM TRAILERS EQUIPED WITH UNDER-FRAME CHANNEL.

PS2658 ~ CA CHANNEL MOUNT GUIDE POLE MOUNT KIT

REPRESENTATION PHOTO MAGIC TILT GUIDE POLE MOUNT ASSEMBLY ~ PS2658 CHANNEL. INCLUDES: 2 x PS2653-1 CLAMP-ON FOR 1-1/2" GUIDE POLES GALV 2 x PS2655 GUIDE PLATE FOR CA SERIES TRAILERS WITH UNDER-FRAME CHANNEL ALUM 4 x PY1701 1/2" x 1-1/2" SQUARE-HEAD BOLT STAINLESS 4 x PY1820 1/2" NYLOCK NUT STAINLESS 4 x PY1905 1/2" FLAT WASHER STAINLESS 8 x PY1710 3/8" x 1-1/4" BOLT STAINLESS 8 x PY1810 3/8" NYLOCK NUT STAINLESS 16 x PY1902 3/8" FLAT WASHER STAINLESS

Roll Brackets

2 sizes available

Rub Pads

2 sizes available