Additional Categories

1/2" Galvanized Hex Head Screws

5 sizes available

1/2" Galvanized Square U-Bolts

15 sizes available

1/2" Stainless Steel Square U-Bolts

2 sizes available

1/2" Stainless Steel Square UBolts

4 sizes available

Heavy-duty U-bolt helps to secure a bracket to your trailer's frame Stainless steel construction is sturdy and resists corrosion Made in the USA

1/4" ALUM "STRAIGHT" CROSS MEMBERS

3 sizes available

1/4" ALUM "V" CROSS MEMBERS

5 sizes available

11GA Galvanized Cross members

XM-71" 3X3 11GA "V"

11GA Galvanized Cross members W/Yoke

2 sizes available

2-PC BOW REST ASSY

BOW REST ASSY W/YLW 3"ROLLER

219-00055-NA ~ SINGLE-EYE HOOK SPRING 27-1/2" KARAVAN

REPRESENTATION PHOTO MAGIC TILT LEAF SPRING ~ 219-00055-NA SINGLE-EYE HOOK SPRINGS ARE MEASURED FROM THE CENTER OF THE FRONT EYE TO THE END OF THE HOOK. INCLUDES .58" ID NYLON SPRING BUSHINGS (ALLOWS FOR GALVANIZED 1/2" BOLT) DOES NOT INCLUDE MOUNTING HARDWARE MOUNTING HARDWARE KITS HARDWARE KITS SPRING EYE BOLT PK1450

3" CHANNEL U-BOLT KIT (Minimum Order of 20 Each)

1 - 7/16X3-1/16X2-13/16 Ubolt, 2- 7/16 Lock Washers, and 2- 7/16 Nut

3"X3" 11GA Galvanized Tongue

9 sizes available

3"X4" Galvanized Tongue

3 sizes available

3"X5" 3/16GA Galvanized Tongue

5 sizes available

3/16" ALUM "STRAIGHT" CROSS MEMBERS

5 sizes available

3/16" ALUM "V" CROSS MEMBERS

7 sizes available

3/8" Stainless Steel Square UBolts

Heavy-duty U-bolt helps to secure a bracket to your trailer's frame Stainless steel construction is sturdy and resists corrosion Made in the USA

5/8" Shafts

3 sizes available

7/16" Bunk Bracket UBolts W/Nuts

Part Qty PY1406 NUT HEX 7/16 HDG 2 PY1515 WASHER FLAT USS 1/2 HDG 2 PY1606 WASHER LOCK 7/16 HDG 2 PY2090 UBOLT 7/16X3-1/16X2-13/16 SQ GALV 1

7/16" Galvanized Square UBolts

2 sizes available

90885 ~ TEKONSHA P2 ELECTRIC BRAKE CONTROLLER

REPRESENTATION PHOTO ** THIS IS A SPECIAL BUY OFFERED AT A GREATLY REDUCE PRICE! ** MAGIC TILT ELECTRIC BRAKE CONTOLLER ~ 90885 The Prodigy P2 electric brake controller supplies power to your tow vehicle's brakes proportionally. This means that your trailer brakes at the same time and with the same strength as your vehicle - even in reverse gear. If you have to slam on your truck's brakes, the trailer's brakes respond instantly, too - there's no delay. Therefore your vehicle's brakes aren't overworked from trying to stop the entire load, and they suffer less wear and tear extending the longevity of your brakes compared to time based controls. The P2 also cuts power to the trailer's brakes when your vehicle is stopped - extending the life of the magnets and brake shoes in the trailer's brake assemblies. Aside from smoother, more efficient braking that results from proportional application of stopping power, the Prodigy P2 also has a boost feature that gives you more initial braking power for those times when you're towing heavier loads. That's when more braking power is needed to stop the trailer at the same time as the tow vehicle. The boost setting sends 13 or 25 percent more power (depending on which setting you choose) back to the trailer brakes, thus compensating for heavier loads. You can boost the power manually at the push of a button as well. The boost feature gets more power to the trailer brakes exactly when you need it most, and your fully loaded rig brakes smoothly and comfortably. This brake controller levels automatically as you drive, so there's no problem using it on steep hills or when towing through the mountains. The self-leveling feature also makes the Prodigy easy to install: Simply mount it in your cab at any vertical angle (it has 360-degree rotation). It's easy to see the display and to access the pivoting manual override lever on the bottom of the unit. The P2's continuous diagnostic check monitors your connection and magnet condition, so you can fix any problems before they land you on the side of the road. This newest version of Tekonsha's popular Prodigy brake controller has reverse battery protection to preserve the unit and accessory systems. And the power-save mode reduces battery drain when the controller isn't in use.

Angles for Single Axle

11 sizes available

Bolt On Swing Tongue Assemblies

4 sizes available

Bow Rest/Roller Guide Components

ROLLER GUIDE[Bar Only 8"]

Carriage Bolts

BOLT 5/16 X 3/4 PLTD

Clamp-On Sockets

2 sizes available

Width4"

COTTER PINS

COTTER PIN 1/8"X1-1/4"[UFP AXLE]

Coupler Repair Kit

COUPLER REPAIR KIT 2" D&L

COUPLERS

3 sizes available

Double Eye Springs

4 sizes available

Galvanized Flat Washers

2 sizes available

Galvanized Hex Head Screws

6 sizes available

Galvanized Hex Nuts

3 sizes available

Galvanized Lock Washers

3 sizes available

Galvanized Plates

2-HOLE PLT.[PWC-4 BACKING PLT.]

Ladders

ALUM TONGUE MOUNTED ASSY

Comes with Hardware to mount

Lug Nuts

CHROME LUG NUT (MCGARD)

NW0192 ~ PINNACLE BOW REST REPLACEMENT BUMPER

REPRESENTATION PHOTO MAGIC TILT D-4 BUMPER ~ NW0192 SOLD INDIVIDUALLY MOUNTING HARDWARE NOT INCLUDED USED ON THE FOLLOWING BOW STOPS (NOT INCLUDED) PO1976 , PO1976N , PO1977 , PO1977N , PO1978 , PO1997 , PO1998

PD2250 ~ LUG NUT 1/2"

REPRESENTATION PHOTO MAGIC TILT LUG NUT ~ PD2250 SOLD INDIVIDUALLY

PD2255 ~ LUG NUT ACORN 1/2" STAINLESS STEEL

REPRESENTATION PHOTO MAGIC TILT ACORN LUG NUT~ PD2255 SOLD INDIVIDUALLY

PD2400 ~ LUG BOLT 1/2" x 1-5/8"

REPRESENTATION PHOTO MAGIC TILT LUG BOLT ~ PD2400 SOLD INDIVIDUALLY

PG2100 ~ BRAKE FLANGE WELD-ON 4-BOLT

REPRESENTATION PHOTO MAGIC TILT BRAKE FLANGE ~ PG2100 FOR USE ON 3500 POUND SPRING AXLES

PG2150 ~ BRAKE FLANGE WELD-ON 5-BOLT

REPRESENTATION PHOTO MAGIC TILT BRAKE FLANGE ~ PG2150

PG3052 ~COUPLER LATCH REPAIR KIT DEXTER / TITAN 4358400

REPRESENTATION PHOTO MAGIC TILT LEVER LOCK REPAIR KIT ~ PG3052 COUPLER REPAIR KIT FOR DEXTER / TITAN MODEL 60 COUPLERS AND BRAKE ACTUATORS

PG3229 ~ TEKONSHA ELECTRIC BRAKE CONTROLLER

REPRESENTATION PHOTO MAGIC TILT ELECTRIC BRAKE CONTOLLER ~ PG3229

PG4823 ~ LATCH PIN KIT 1-1/4" DEXTER / UFP

REPRESENTATION PHOTO MAGIC TILT HITCH PIN KIT ~ PG4823 INCLUDES : PIN, CLIP, AND CABLE WILL NOT WORK ON NEWER IN-LINE STYLE ACTUATORS

PG4824 ~ ROLLER PIN / PAD SERVICE KIT A160 ACTUATOR DEXTER / UFP K71-772-00

REPRESENTATION PHOTO MAGIC TILT ACTUATOR REPAIR KIT ~ PG4824 PROVIDES REPLACEMENT WEAR ITEMS FOR SMOOTH OPERATION. INCLUDES: 2 X RUB PADS 7-5/8" x 3-3/8" x 1" 2 X BUSHINGS 15/16" OD x 1-1/4" 4 X ROLLER PINS 3/4" x 4-5/16" 8 X SNAP RINGS 3/4"

PG4857 ~ BANJO BOLT

REPRESENTATION PHOTO MAGIC TILT BANJO BOLT ~ PG4857 USE WITH: SINGLE BANJO FITTING PG4855 OR DOUBLE BANJO FITTING PG4856 COPPER WASHERS PG4858

PG4858 ~ COPPER WASHER BANJO FITTING (UFP)

REPRESENTATION PHOTO MAGIC TILT BANJO WASHER ~ PG4858 USE WITH: SINGLE BANJO FITTING PG4855 OR DOUBLE BANJO FITTING PG4856 BANJO BOLT PG4857

PG4859 ~ CALIPER BLEEDER SCREW (DEXTER / UFP)

REPRESENTATION PHOTO MAGIC TILT BLEEDER SCREW ~ PG4859

PG5007 ~ DISC CALIPER BOLT 7/16" x 1" DEXTER / UFP

REPRESENTATION PHOTO MAGIC TILT CALIPER BOLT ~ PG5007 USES 3/8" ALLEN WRENCH

PH1305 ~ ZERC FITTING POSI-LUBE (DEXTER / UFP)

REPRESENTATION PHOTO MAGIC TILT ZERC FITTING ~ PH1305 SOLD INDIVIDUALLY FOR SPINDLE END ON POSI-LUBE SPINDLES

PH1752 ~ SPINDLE 1-1/16" x 1-1/16" 1.5K UCF

REPRESENTATION PHOTO MAGIC TILT SPINDLE ~ PH1752

PH1903 ~ SPINDLE 1-1/4" x 1-3/4" 5-6K DEXTER / UFP

REPRESENTATION PHOTO MAGIC TILT SPINDLE ~ PH1903 6,000 POUNDS (8-LUG)

PH1906 ~ SPINDLE 1-1/4" x 1-3/4" 5-6K DEXTER / UFP

REPRESENTATION PHOTO MAGIC TILT SPINDLE ~ PH1906 6,000 POUNDS (8-LUG)

PH1980 ~ SPINDLE NUT 13/16"

REPRESENTATION PHOTO MAGIC TILT SPINDLE NUT ~ PH1980 SOLD INDIVIDUALLY

PH2000 ~ SPINDLE NUT 1"

REPRESENTATION PHOTO MAGIC TILT SPINDLE NUT ~ PH2000 SOLD INDIVIDUALLY

PH2050 ~ AXLE WASHER 3/4" F436

REPRESENTATION PHOTO MAGIC TILT AXLE WASHER ~ PH2050 SOLD INDIVIDUALLY

PH2060 ~ AXLE WASHER 1"

REPRESENTATION PHOTO MAGIC TILT AXLE WASHER ~ PH2060 SOLD INDIVIDUALLY

PH2065 ~ AXLE D WASHER 3/4" x 13/16" x .137" (DEXTER / UFP)

REPRESENTATION PHOTO MAGIC TILT AXLE WASHER ~ PH2065 SOLD INDIVIDUALLY THINNER. USED ON 2000 TO 3500 LB. UFP AXLES

PH2066 ~ AXLE D WASHER 3/4" x 13/16" x .184" (DEXTER / UPF)

REPRESENTATION PHOTO MAGIC TILT AXLE WASHER ~ PH2066 SOLD INDIVIDUALLY THICKER. USED ON 5000 LB. AND GREATER UFP AXLES

PH2070 ~ AXLE D WASHER 1"

REPRESENTATION PHOTO MAGIC TILT AXLE WASHER ~ PH2070 SOLD INDIVIDUALLY

PH2105 ~ TANG WASHER 1"

REPRESENTATION PHOTO MAGIC TILT TANG WASHER ~ PH2105 SOLD INDIVIDUALLY

PH2108 ~ SPINDLE NUT RETAINER

REPRESENTATION PHOTO MAGIC TILT SPINDLE NUT RETAINER ~ PH2108 SOLD INDIVIDUALLY

PJ1350 ~ DOUBLE-EYE SPRING 20"

REPRESENTATION PHOTO MAGIC TILT LEAF SPRING ~ PJ1350 # LEAF: 3 DOUBLE-EYE SPRINGS ARE MEASURED FROM THE CENTER OF THE FRONT EYE TO THE CENTER OF THE REAR EYE. INCLUDES .58" ID NYLON SPRING BUSHINGS (ALLOWS FOR GALVANIZED 1/2" BOLT) DOES NOT INCLUDE MOUNTING HARDWARE MOUNTING HARDWARE KITS HARDWARE KITS

PK1000 ~ 1-AXLE MOUNT KIT 1-EYE 1-1/2" AXLE GALVANIZED

REPRESENTATION PHOTO MAGIC TILT SINGLE AXLE MOUNT KIT ~ PK1000 Provides all necessary hardware to mount single-eye springs on one 1-1/2" square axle. FOR CORRECT U-BOLT, SELECT NUMBER OF SPRING LEAVES IN DROP-DOWN INCLUDES: 2 x PK1200 3-HOLE PLATES GALVANIZED 2 x CAPSCREW 1/2" x 3-1/2" GR 5 PLATED 2 x NUT NYLOC 1/2-13 PLATED 4 x NUT HEX 1/2-13 GALVANIZED 4 x WASHER FLAT 1/2" GALVANIZED 4 x WASHER LOCK 1/2" GALVANIZED 2 x U-BOLT 1/2" x 2-3/4" x SELECT GALVANIZED

PK1050 ~ 1-AXLE MOUNT KIT 1-EYE 2x2 AXLE GALVANIZED

REPRESENTATION PHOTO MAGIC TILT SINGLE AXLE MOUNT KIT ~ PK1050 PROVIDES ALL NECESSARY HARDWARE TO MOUNT SINGLE-EYE SPRINGS ON ONE 2" SQUARE AXLE FOR CORRECT U-BOLT, SELECT NUMBER OF SPRING LEAVES IN DROP-DOWN 3, 4, 5, 6 INCLUDES: 2 x PK1250 5-HOLE PLATES GALV 2 x CAPSCREW 1/2" x 3-1/2" GR 5 PLATED 2 x NUT NYLOCK 1/2-13 PLATED 8 x NUT HEX 1/2-13 GALV 8 x WASHER FLAT USS 1/2" GALV 8 x WASHER LOCK 1/2" GALV 4 x U-BOLT 1/2" x 2-1/16" x SELECT GALV

PK1050-1 ~ 1-AXLE MOUNT KIT 1-EYE 2x3 AXLE GALVANIZED

REPRESENTATION PHOTO MAGIC TILT SINGLE AXLE MOUNT KIT ~ PK1050-1 PROVIDES ALL NECESSARY HARDWARE TO MOUNT SINGLE-EYE SPRINGS ON ONE 2" x 3" AXLE FOR CORRECT U-BOLT, SELECT NUMBER OF SPRING LEAVES IN DROP-DOWN 3, 4, 5, 6 INCLUDES: 2 x PK1250 5-HOLE PLATES GALV 2 x CAPSCREW 1/2" x 3-1/2" GR 5 PLATED 2 x NUT NYLOCK 1/2-13 PLATED 8 x NUT HEX 1/2-13 GALV 8 x WASHER FLAT USS 1/2" GALV 8 x WASHER LOCK 1/2" GALV 4 x U-BOLT 1/2" x 2-1/16" x SELECT GALV

PK1100 ~ 1-AXLE MOUNT KIT 2-EYE 2x2 AXLE GALVANIZED

REPRESENTATION PHOTO MAGIC TILT SINGLE AXLE MOUNT KIT ~ PK1100 Provides all necessary hardware to mount double-eye springs on one 2" square axle. FOR CORRECT U-BOLT, SELECT NUMBER OF SPRING LEAVES IN DROP-DOWN 3, 4, 5, 6 INCLUDES: 2 x PK1250 5-HOLE PLATES GALV 4 x PK1300 2-HOLE SHACKLE PLATE GALV 2 x SPACER DOUBLE EYE SPRING 1-3/4" ALUM 6 x CAPSCREW 1/2" x 3-1/2" GR 5 PLATED 6 x NUT NYLOCK 1/2-13 PLATED 8 x NUT HEX 1/2-13 GALV 12 x WASHER FLAT USS 1/2" GALV 8 x WASHER LOCK 1/2" GALV 4 x U-BOLT 1/2" x 2-1/16" x SELECT GALV

PK1100-1 ~ 1-AXLE MOUNT KIT 2-EYE 2x3 AXLE GALVANIZED

REPRESENTATION PHOTO MAGIC TILT SINGLE AXLE MOUNT KIT ~ PK1100-1 Provides all necessary hardware to mount double-eye springs on one 2" x 3" square axle. FOR CORRECT U-BOLT, SELECT NUMBER OF SPRING LEAVES IN DROP-DOWN 3, 4, 5, 6 INCLUDES: 2 x PK1250 5-HOLE PLATE GALV 4 x PK1300 2-HOLE SHACKLE PLATE GALV 2 x SPACER D-EYE SPRING 1-3/4" ALUM 6 x GRADE-5 BOLT (1/2" x 3-1/2") PLATED 6 x 1/2" NYLOCK NUT PLATED 8 x 1/2" HEX NUT GALV 12 x 1/2" FLAT WASHER GALV 8 x 1/2" LOCK WASHER GALV 4 x SQUARE U-BOLT 1/2" x 2-1/16" x SELECT GALV

PK1100-SS ~ 1-AXLE MOUNT KIT 2-EYE 2x2 AXLE STAINLESS / GALV

REPRESENTATION PHOTO MAGIC TILT SINGLE AXLE MOUNT KIT ~ PK1100-SS Provides all necessary hardware to mount double-eye springs on one 2" square axle. FOR CORRECT U-BOLT, SELECT NUMBER OF SPRING LEAVES IN DROP-DOWN 3, 4, 5, 6 INCLUDES: 2 x PK1250 5-HOLE PLATES GALV 4 x PK1300 2-HOLE SHACKLE PLATE GALV 2 x SPACER DOUBLE EYE SPRING 1-3/4" ALUM 6 x CAPSCREW 1/2" x 3-1/2" GR 5 PLATED 6 x NUT NYLOCK 1/2-13 PLATED 8 x NUT HEX 1/2-13 STAINLESS 12 x WASHER FLAT USS 1/2" GALV 8 x WASHER LOCK 1/2" STAINLESS 4 x U-BOLT 1/2" x 2-1/16" x SELECT STAINLESS

PK1150 ~ 2-AXLE MOUNT KIT 2-EYE 2x2 AXLE GALVANIZED

REPRESENTATION PHOTO MAGIC TILT TANDEM AXLE MOUNT KIT ~ PK1150 Provides all necessary hardware to mount double-eye springs on two 2" square axles. SPRING TYPE DOUBLE-EYE FOR CORRECT U-BOLT, SELECT NUMBER OF SPRING LEAVES IN DROP-DOWN 3, 4, 5, 6 INCLUDES: 4 x PK1250 5-HOLE PLATES GALV 8 x PK1300 2-HOLE SHACKLE PLATE GALV 12 x CAPSCREW 1/2" x 3-1/2" GR 5 PLATED 2 x CAPSCREW 1/2" x 4" GR 5 PLATED 14 x NUT NYLOCK 1/2-13 PLATED 16 x NUT HEX 1/2-13 GALV 28 x WASHER FLAT USS 1/2" GALV 16 x WASHER LOCK 1/2" GALV 8 x U-BOLT 1/2" x 2-1/16" x SELECT GALV

PK1150-SS ~ 2-AXLE MOUNT KIT 2-EYE 2x2 AXLE STAINLESS / GALV

REPRESENTATION PHOTO MAGIC TILT TANDEM AXLE MOUNT KIT ~ PK1150-SS Provides all necessary hardware to mount double-eye springs on two 2" square axles. FOR CORRECT U-BOLT, SELECT NUMBER OF SPRING LEAVES IN DROP-DOWN 3, 4, 5, 6 INCLUDES: 4 x PK1250 5-HOLE PLATES GALV 8 x PK1300 2-HOLE SHACKLE PLATE GALV 12 x CAPSCREW 1/2" x 3-1/2" GR 5 PLATED 2 x CAPSCREW 1/2" x 4" GR 5 PLATED 14 x NUT NYLOCK 1/2-13 PLATED 16 x NUT HEX 1/2-13 STAINLESS 28 x WASHER FLAT USS 1/2" GALV 16 x WASHER LOCK 1/2" STAINLESS 8 x U-BOLT 1/2" x 2-1/16" x SELECT STAINLESS

PK1152 ~ 2-AXLE MOUNT KIT 2-EYE 2x3 AXLE GALVANIZED

REPRESENTATION PHOTO MAGIC TILT TANDEM AXLE MOUNT KIT ~ PK1152 Provides all necessary hardware to mount double-eye springs on two 2" x 3" axles. FOR CORRECT U-BOLT, SELECT NUMBER OF SPRING LEAVES IN DROP-DOWN 3, 4, 5, 6 INCLUDES: 4 x PK1250 5-HOLE PLATES GALV 8 x PK1300 2-HOLE SHACKLE PLATE GALV 12 x CAPSCREW 1/2" x 3-1/2" GR 5 PLATED 2 x CAPSCREW 1/2" x 4" GR 5 PLATED 14 x NUT NYLOCK 1/2-13 PLATED 16 x NUT HEX 1/2-13 GALV 28 x WASHER FLAT USS 1/2" GALV 16 x WASHER LOCK 1/2" GALV 8 x U-BOLT 1/2" x 2-1/16" x SELECT GALV

PK1152-SS ~ 2-AXLE MOUNT KIT 2-EYE 2x3 AXLE STAINLESS / GALV

REPRESENTATION PHOTO MAGIC TILT TANDEM AXLE MOUNT KIT ~ PK1152-SS Provides all necessary hardware to mount double-eye springs on two 2" x 3" square axles FOR CORRECT U-BOLT, SELECT NUMBER OF SPRING LEAVES IN DROP-DOWN 3, 4, 5, 6 INCLUDES: 4 x PK1250 x 5-HOLE PLATES GALV 8 x PK1300 x 2-HOLE PLATES GALV 12 x PY0260 x CAPSCREW 1/2 x 3-1/2 GR5 PLATED 2 x PY0265 x CAPSCREW 1/2 x 4 GR5 PLATED 16 x PY1025 x LOCK WASHER 1/2 STAINLESS 14 x PY1315 x NUT NYLOCK 1/2-13 PLATED 28 x PY1515 x FLAT WASHER USS 1/2 GALV 16 x PY1785 x HEX NUT 1/2" STAINLESS 16 x PY1905 x FLAT WASHER 1/2" STAINLESS 8 x PY2538 x U-BOLT SS 1/2 x 2-1/16 x SELECT GALV

PK1153 ~ 3-AXLE MOUNT KIT 2-EYE 2x3 AXLE GALVANIZED

REPRESENTATION PHOTO MAGIC TILT TRIPLE AXLE MOUNT KIT ~ PK1153 Provides all necessary hardware to mount double-eye springs on three 2" x 3" axles. FOR CORRECT U-BOLT, SELECT NUMBER OF SPRING LEAVES IN DROP-DOWN 3, 4, 5, 6 INCLUDES: 6 x PK1250 x 5-HOLE PLATES GALV 16 x PK1300 x 2-HOLE SHACKLE PLATE GALV 20 x PY0260 x CAPSCREW 1/2" x 3-1/2" GR 5 PLATED 4 x PY0265 x CAPSCREW 1/2" x 4" GR 5 PLATED 24 x PY1315 x NUT NYLOCK 1/2-13 PLATED 24 x PY1410 x NUT HEX 1/2-13 GALV 48 x PY1515 x WASHER FLAT USS 1/2" GALV 24 x PY1610 x WASHER LOCK 1/2" GALV 12 x PY2050 x U-BOLT 1/2" x 2-1/16" x SELECT GALV

PK1200 ~ 3-HOLE PLATE GALVANIZED

REPRESENTATION PHOTO MAGIC TILT 3-HOLE PLATE ~ PK1200

PK1205 ~ 3-HOLE BUNK PLATE GALVANIZED

REPRESENTATION PHOTO MAGIC TILT 3-HOLE BUNK PLATE ~ PK1205

PK1250 ~ 5-HOLE PLATE GALVANIZED

REPRESENTATION PHOTO MAGIC TILT 5-HOLE PLATE ~ PK1250

PK1300 ~ 2-HOLE SHACKLE PLATE GALVANIZED

REPRESENTATION PHOTO MAGIC TILT 2-HOLE SHACKLE PLATE ~ PK1300

PK1320 ~ 1-HOLE SLOT PLATE GALVANIZED

REPRESENTATION PHOTO MAGIC TILT 1-HOLE SLOT PLATE ~ PK1320

PK1450 ~ SPRING-EYE BOLT WITH LOCK NUT 1/2" x 3-1/2"

REPRESENTATION PHOTO MAGIC TILT BOLT W/ NUT ~ PK1450 SPRING EYE BOLTS NEED TO BE GRADE 5 AND HAVE A NYLOCK NUT STAINLESS STEEL BOLTS TO NOT MEET THE STRENGTH REQUIREMENTS AND GALVANIZED NYLOCK NUTS DO NOT EXIST BOLTS SHOULD NOT BE TOO TIGHT. SPRINGS MUST BE ALLOWED TO MOVE FREELY AROUND THE EYE BOLTS

PK1701 ~ SPRING HANGER 1-PIECE STANDARD GALVANIZED

REPRESENTATION PHOTO MAGIC TILT SPRING HANGER ~ PK1701 WORK ON FRONT OR REAR OF SPRINGS. WINGS ARE SPREAD TO ACCOMMODATE PIVOT SHACKLES AT REAR. IF NO PIVOT SHACKLES ARE USED (FRONT MOUNT, ONE-EYE SPRINGS) YOU CAN PULL THE WINGS DOWN TO 90° WITH THE SPRING EYE BOLT. SPRING-EYE BOLT PK1450 (NOT INCLUDED)

PK1702 ~ SPRING HANGER 2-PIECE HEAVY-DUTY GALVANIZED

REPRESENTATION PHOTO MAGIC TILT SPRING HANGER ~ PK1702

PK1702-T ~ SPRING HANGER 2-PIECE CA-SERIES 2-BOLT GALVANIZED

REPRESENTATION PHOTO MAGIC TILT SPRING HANGER ~ PK1702-T USE WITH PY1701 SQUARE MOUNT BOLTS

PK1703 ~ SPRING HANGER 2-PIECE MEDIUM-DUTY GALVANIZED

REPRESENTATION PHOTO MAGIC TILT SPRING HANGER ~ PK1703

PK1731 ~ SLIPPER SPRING HANGER GALVANIZED

REPRESENTATION PHOTO MAGIC TILT SLIPPER SPRING HANGER ~ PK1731 MOUNTS THROUGH 2"-WIDE TUBE FRAME FOR SINGLE-EYE SPRING REAR HANGER

PK1800 ~ EQUALIZER BOLT-ON PLATE 5-3/4 in GALVANIZED

REPRESENTATION PHOTO MAGIC TILT EQUALIZER PLATE ~ PK1800

PK1800-T ~ EQUALIZER BOLT-ON PLATE 5-3/4" CA-SERIES GALVANIZED

REPRESENTATION PHOTO MAGIC TILT EQUALIZER PLATE ~ PK1800-T USE WITH PY1701 SQUARE MOUNT BOLTS

PK1810 ~ EQUALIZER BOLT-ON PLATE 4-1/2 in GALVANIZED

REPRESENTATION PHOTO MAGIC TILT EQUALIZER PLATE ~ PK1810

PK1950 ~ EQUALIZER "6-1/2" GALVANIZED

REPRESENTATION PHOTO MAGIC TILT EQUALIZER ~ PK1950 INCLUDES NYLON BUSHINGS

PK2000 ~ EQUALIZER "8" INCH GALVANIZED

REPRESENTATION PHOTO MAGIC TILT EQUALIZER ~ PK2000 INCLUDES NYLON BUSHINGS

PK2513 ~ 1-AXLE UNDERCARRIAGE 38" 2-EYE OUTSIDE MOUNT

REPRESENTATION PHOTO MAGIC TILT UNDERCARRIAGE ~ PK2513 WILL WORK ON EITHER LEFT OR RIGHT SIDES 31" BETWEEN STEP MOUNTS USED ON ALUMINUM FRAME TRAILERS HOLE SIZE FOR MOUNTING TO FRAME: 1/2" BOLT PATTERN FOR MOUNTING TO FRAME MAY NOT MATCH EXISTING UNDERCARRIAGE AXLE & SPRING-TO-UNDERCARRIAGE HARDWARE KITS: 2x2 AXLES: GALVANIZED PK1100 , STAINLESS/GALV PK1100-SS 2x3 AXLES: GALVANIZED PK1100-1

PK2550 ~ 2-AXLE UNDERCARRIAGE 63-1/2" NO STEPS

REPRESENTATION PHOTO MAGIC TILT UNDERCARRIAGE ~ PK2550 NO STEPS, FENDER BRACKETS, FRAME MOUNT HOLES USES TWO U-BOLTS TO GO AROUND TUBE OR C-CHANNEL FRAMES (NOT INCLUDED) BOTTOM CAN BE DRILLED TO BOLT DIRECTLY UNDER AN I-BEAM FRAME AXLE & SPRING-TO-UNDERCARRIAGE HARDWARE KITS: 2x2 AXLES: GALVANIZED PK1150 , STAINLESS/GALV PK1150-SS 2x3 AXLES: GALVANIZED PK1152 , STAINLESS/GALV PK1152-SS

PK2655 ~ 2-AXLE UNDERCARRIAGE 71" 68" FENDERS FOR ALUMINUM STEPS

Magic Tilt Undercarriage ~ PK2655 Good to know: Primarily used on aluminum i-beam trailers Hole size for mounting to frame: 1/2" On 4-1/4" Centers Bolt pattern for mounting to frame may not match existing undercarriage Axle & Spring-to-undercarriage hardware kits: 2x2 Axles: Galvanized PK1150 , Stainless/Galv PK1150-SS 2x3 Axles: Galvanized PK1152 , Stainless/Galv PK1152-SS

PK2705 ~ 2-AXLE UNDERCARRIAGE 78" WITH STEPS

REPRESENTATION PHOTO MAGIC TILT UNDERCARRIAGE ~ PK2705 NO FRAME MOUNTING HOLES PRIMARILY USED ON GALVANIZED TRAILERS USES TWO U-BOLTS TO GO AROUND TUBE OR C-CHANNEL FRAMES (NOT INCLUDED) AXLE & SPRING-TO-UNDERCARRIAGE HARDWARE KITS: 2x2 AXLES: GALVANIZED PK1150 , STAINLESS/GALV PK1150-SS 2x3 AXLES: GALVANIZED PK1152 , STAINLESS/GALV PK1152-SS

PK2770 ~ 3-AXLE UNDERCARRIAGE 112" WITH STEPS

REPRESENTATION PHOTO (PLEASE CALL 941-358-1117 FOR SHIPPING QUOTE) MAGIC TILT UNDERCARRIAGE ~ PK2770 NO FRAME MOUNTING HOLES USED ON ALUMINUM AND GALVANIZED TRAILERS USES U-BOLTS TO GO AROUND TUBE OR C-CHANNEL FRAMES (NOT INCLUDED) AXLE & SPRING-TO-UNDERCARRIAGE HARDWARE KIT: PK1153

Plated Ni-Lock Nuts

3 sizes available

PM1005 ~ PWC WINCH W/ ARM

REPRESENTATION PHOTO MAGIC TILT PWC WINCH WITH ARM ~ PM1005 INCLUDES PM1000 WINCH WITH STRAP CAN BE USED WITH 3" BOW ROLLERS OR RUBBER V-BLOCK (NOT INCLUDED) BOLTS THROUGH ANY WINCH POST (HARDWARE NOT INCLUDED)

PO2610 ~ CROSSMEMBER GALVANIZED PONTOON 2" x 2" x 96"

REPRESENTATION PHOTO MAGIC TILT CROSS-MEMBER ~ PO2610 (PLEASE CALL 941-358-1117 FOR SHIPPING QUOTE) DOES NOT HAVE ANY PRE-DRILLED HOLES END PLUGS NOT INCLUDED

PO2612 ~ CROSSMEMBER GALVANIZED PONTOON 2" x 2" x 84"

REPRESENTATION PHOTO MAGIC TILT CROSS-MEMBER ~ PO2612 DOES NOT HAVE ANY PRE-DRILLED HOLES END PLUGS NOT INCLUDED

PO2861 ~ LADDER ASSEMBLY TONGUE MOUNT ALUMINUM

REPRESENTATION PHOTO MAGIC TILT LADDER ASSEMBLY TONGUE MOUNT ~ PO2861 SHIPS LTL ON PALLET - PLEASE CALL 941-358-1117 FOR SHIPPING QUOTE SPECIAL ORDER. PLEASE ALLOW ADDITIONAL TIME TONGUE MOUNTING HARDWARE NOT INCLUDED

PO3520 ~ WINCH POST 1-1/2" x 1-1/2" x 24" PWC

REPRESENTATION PHOT MAGIC TILT PWC WINCH POST ~ PO3520 UTILIZES PO2042 PWC WINCH/BOW STOP CAN BE THROUGH-BOLTED ON I-BEAMS DOES NOT INCLUDE MOUNTING HARDWARE OR PO3538 END PLUG

PR1650 ~ ROLLER SHAFT CAP NUT 5/8"

REPRESENTATION PHOTO MAGIC TILT ROLLER SHAFT CAP NUT ~ PR1650 SOLD INDIVIDUALLY USED WITH VARIOUS KEEL ROLLER MOUNTS AND 5/8" ROLLER SHAFTS

Pro I-Beam Jack Mounts

2 sizes available

PS2150 ~ SET SCREW WITH NUT 7/16" x 1-1/2"

REPRESENTATION PHOTO MAGIC TILT SET SCREW ~ PS2150 REPLACEMENT SET SCREW FOR PS2640 ASSEMBLY USED WITH THE PS2649 , PS2310 & PS2401 CLAMP-ON SOCKETS AND PS2210 NUT RETAINER (NOT INCLUDED)

PS2210 ~ NUT RETAINER PLATE

REPRESENTATION PHOTO MAGIC TILT NUT RETAINER PLATE ~ PS2210 REPLACEMENT RETAINER FOR PS2640 ASSEMBLY USED WITH THE PS2649 AND PS2310 & PS2401 CLAMP-ON SOCKETS AND PS2150 SET SCREW (NOT INCLUDED)

PS2640 ~ CLAMP-ON ASSEMBLY 3" x 1-1/2" TUBE

REPRESENTATION PHOTO MAGIC TILT CLAMP-ON ASSEMBLY ~ PS2640 DESIGNED TO MOUNT HORIZONTAL BUNKS TO 3" x 3" CROSSMEMBERS INCLUDES: 1 x PS2150 SET SCREW W/ NUT PLATED 1 x PS2210 NUT RETAINER PLATE GALV 1 x PS2649 3" x 3" CLAMP-ON SOCKET GALV 1 x PT1760 BUNK RISER 1-1/2" x 1-1/2" x 12" SQUARE GALV 1 x PT2070 PIVOT L BRACKET GALV 2 x PY0409 LAG SCREW 3/8" x 1-1/4" PLATED 3 x PY1405 HEX NUT 3/8-16 GALV 3 x PY1505 FLAT WASHER 3/8" GALV 3 x PY1605 LOCK WASHER 3/8" GALV 1 x PY1615 BOLT 3/8" x 2-1/2" GALV 2 x PY1624 BOLT 3/8" x 4-1/2" GALV

PS2649 ~ CLAMP-ON SOCKET 3" x 1-1/2" TUBE

REPRESENTATION PHOTO MAGIC TILT CLAMP-ON SOCKET ~ PS2649 DESIGNED TO MOUNT HORIZONTAL BUNKS TO 3" x 3" CROSSMEMBERS REPLACEMENT SOCKET FOR THE PS2640 ASSEMBLY MOUNTS OVER CROSSMEMBER WITH 3/8" x 4-1/2" GALVANIZED BOLT (NOT INCLUDED) REQUIRES ONE EACH PS2210 NUT RETAINER AND PS2150 SET SCREW (NOT INCLUDED) USE WITH PRE-CUT 1-1/2" TUBE BRACKETS OR BULK TUBE BRACKETS (NOT INCLUDED)

PS2652 ~ CLAMP-ON SOCKET 3" x 2" TUBE

REPRESENTATION PHOTO MAGIC TILT CLAMP-ON SOCKET ~ PS2652 USED TO MOUNT ANY BOW REST OR BUNK GUIDE USING 2" x 2" VERTICAL TUBING REQUIRES TWO PS2150 SET SCREWS (NOT INCLUDED) MOUNTS TO 3" x 3" CROSSMEMBERS WITH TWO 3/8" x 4-1/2" GALVANIZED BOLTS (NOT INCLUDED) USE WITH PU4040 2" TUBE (NOT INCLUDED)

PS2653-1 ~ CLAMP-ON TOP HAT 1-1/2" GALVANIZED

REPRESENTATION PHOTO MAGIC TILT CLAMP-ON SOCKET ~ PS2653-1

PS2700 ~ CROSS-MEMBER YOKE 3" STRAIGHT GALVANIZED

REPRESENTATION PHOTO MAGIC TILT 3" CROSS-MEMBER YOKE ~ PS2700 WRAPS OVER 3" TALL BY 1-1/2" OR 2" WIDE FRAME RAIL TO ATTACH A 3" TALL STRAIGHT CROSSMEMBER IF ATTACHING A VEE CROSSMEMBER, USE YOKE PS2701

PS2701 ~ CROSS-MEMBER YOKE 3" VEE GALVANIZED

REPRESENTATION PHOTO MAGIC TILT 3" CROSS-MEMBER YOKE ~ PS2701 WRAPS OVER 3" TALL BY 1-1/2" OR 2" WIDE FRAME RAIL TO ATTACH A 3" TALL VEE (SMILE) CROSSMEMBER IF ATTACHING A STRAIGHT CROSSMEMBER OVER A 3" TALL x 1-1/2" OR 2" FRAME, USE YOKE PS2700 CAN BE USED TO ATTACH A 3" STRAIGHT CROSSMEMBER OVER A 3" x 3" FRAME

PU2258 ~ COUPLER 2-5/16" BALL

16,000 LBS. (DEMCO)

REPRESENTATION PHOTO MAGIC TILT COUPLER ~ PU2258 RAISE LATCH, SEAT COUPLER ON BALL & LATCH AUTOMATICALLY SNAPS TO LOCKED POSITION MOUNTING HARDWARE NOT INCLUDED

PU2270 ~ COUPLER ADJUSTABLE 2-5/16"

20K (DEXTER / UFP)

REPRESENTATION PHOTO MAGIC TILT COUPLER ~ PU2270 USED ON LARGE TRAILERS UTILIZING ELECTRIC-OVER-HYDRAULIC BRAKES USE WITH (NOT INCLUDED): ONE PU2272 CHANNEL BRACKET TWO PY0285 5/8"x4-1/2" GRADE 8 BOLTS TWO PY1320 5/8" NYLOCK NUTS

PU2272 ~ COUPLER BRACKET ADJUSTABLE (DEXTER / UFP)

REPRESENTATION PHOTO MAGIC TILT COUPLER BRACKET ~ PU2272 USED ON LARGE TRAILERS UTILIZING ELECTRIC-OVER-HYDRAULIC BRAKES 4-HOLE, 3 POSITION ADJUSTMENT USE WITH (NOT INCLUDED): ONE PU2270 COUPLER TWO PY0285 5/8" x 4-1/2" GRADE 8 BOLTS TWO PY1320 5/8" NYLOCK NUTS

PU6000 ~ CROSSMEMBER GALVANIZED C-CHANNEL 3"

REPRESENTATION PHOTO MAGIC TILT 3" FRAME CHANNEL ~ PU6000 (PLEASE CALL 941-358-1117 FOR SHIPPING QUOTE) SPECIAL ORDER, PLEASE ALLOW ADDITIONAL TIME

PV0905 ~ FIXED TONGUE JACK 1000 LBS.

Magic Tilt Tongue Jack ~ PV0905 Good to know: Includes Mounting Hardware Does Not Pivot Replacement Wheel PV3150

PV0965 ~ TONGUE JACK DUAL SWIVEL 1500 LBS.

REPRESENTATION PHOTO MAGIC TILT TONGUE JACK ~ PV0965 INCLUDES MOUNTING HARDWARE REPLACEMENT WHEEL 2 x PV3150

PV0976 ~ TONGUE JACK SQUARE TUBE 2500 LBS.

REPRESENTATION PHOTO MAGIC TILT TONGUE JACK ~ PV0976 INCLUDES MOUNTING HARDWARE REPLACEMENT DROP-LEG INSERT PV0980-LEG REPLACEMENT PIN PV0980-PIN

PV0980-LEG ~ TONGUE JACK LEG & SAND FOOT

REPRESENTATION PHOTO MAGIC TILT JACK LEG & PLATE ~ PV0980-LEG REPLACEMENT DROP LEG FOR PV0976 JACK AND MOST MARINE DROP-LEG JACKS. REPLACEMENT PIN PV0980-PIN (NOT INCLUDED)

PV0980-PIN ~ TONGUE JACK LOCKING PIN 1/2 in x 3-1/2 in

REPRESENTATION PHOTO MAGIC TILT LOCKING PIN ~ PV0980-PIN REPLACEMENT PIN FOR PV0976 JACK AND MOST DROP-LEG JACKS

PV1150 ~ TONGUE JACK SWIVEL MOUNT 1200 LBS.

REPRESENTATION PHOTO MAGIC TILT TONGUE JACK ~ PV1150 INCLUDES MOUNTING HARDWARE CAN BE ADAPTED TO 4-1/2" AND 5-1/2" I-BEAM FRAMES WITH A FRAME-MOUNT PLATE . REPLACEMENT WHEEL PV3150

PV1154 ~ TONGUE JACK SWIVEL MOUNT 1500 LBS.

REPRESENTATION PHOTO MAGIC TILT TONGUE JACK ~ PV1154 INCLUDES MOUNTING HARDWARE CAN BE ADAPTED TO 4-1/2" AND 5-1/2" I-BEAM FRAMES WITH A FRAME-MOUNT PLATE .

PV2158 ~ TUBE GUIDE ASSY STANDARD W/ U-BOLTS

REPRESENTATION PHOTO MAGIC TILT STANDARD TUBE GUIDE ASSEMBLY ~ PV2158 PLEASE CALL 941-358-1117 FOR SHIPPING QUOTE INCLUDES: 2 x PV2159-66G STANDARD GUIDE POLE 2 x PV2157 60" PVC SLEEVE WITH CAP 8 x NUT HEX 3/8-16 GALV 8 x WASHER FLAT 3/8" GALV 8 x WASHER LOCK 3/8" GALV 4 x U-BOLT 3/8" x 1-9/16" x 2-5/8" GALV OPTIONAL GUIDE POLE COVERS (62x30x5)

PV2281 ~ BARE BOW REST "Y" (NO GUIDE)

REPRESENTATION PHOTO MAGIC TILT BARE BOW REST ~ PV2281 NO PRE-DRILLED HOLES REPLACEMENT REST FOR PS5100 ASSEMBLY CAN USE WITH INDIVIDUALLY WITH PP2245 RUB PAD OR IN PAIRS WITH 2x4 AND 2x6 HORIZONTAL BUNKS MOUNTING HARDWARE (NOT INCLUDED): EITHER PS2652 CLAMP-OVER OR TOP HAT CLAMPS OR ASSEMBLIES

PV2282-3 ~ BOW REST ROLLER GUIDE ASSEMBLY

REPRESENTATION PHOTO MAGIC TILT ROLLER GUIDE ASSEMBLY ~ PV2282-3 HEIGHT ABOVE CROSSMEMBER: REQUIRES 2" CLAMP-ON ASSEMBLY (NOT INCLUDED)

PV3150 ~ TONGUE JACK WHEEL

REPRESENTATION PHOTO MAGIC TILT TONGUE JACK WHEEL ~ PV3150 USES PY0260 BOLT AND PY1315 NUT (NOT INCLUDED)

PV9918 ~ DOT C2 REFLECTIVE TAPE (PER FOOT)

REPRESENTATION PHOTO MAGIC TILT REFLECTIVE TAPE ~ PV9918 SOLD PER FOOT REQUIRED ON TRAILERS 10,000 POUNDS GVWR OR HIGHER

PY0491 ~ SELF-TAPPING SCREW

REPRESENTATION PHOTO MAGIC TILT SELF-TAPPING SCREW ~ PY0491 USED TO FASTEN RUB PADS TO CROSSMEMBERS

PY1291 ~ SERRATED FLANGE NUT 5/16-18 PLATED

REPRESENTATION PHOTO MAGIC TILT SERRATED FLANGE NUT ~ PY1291

PY1345 ~ RETAINER PIN PLATED

REPRESENTATION PHOTO MAGIC TILT RETAINER PIN ~ PY1345 USED WITH SWING TONGUE HITCH PINS

PY1388 ~ EYE BOLT 3/8" x 3-1/2" GALV

REPRESENTATION PHOTO MAGIC TILT EYE BOLT ~ PY1388 USE IN SIDES OF VERTICAL BUNKS FOR TRANSOM STRAPS

PY1496 ~ FANGED BOLT 5/16" x 2-1/4" GALVANIZED

REPRESENTATION PHOTO MAGIC TILT FANGED BOLT ~ PY1496 REPLACES BOTTOM-MOUNT LAG SCREWS. INSERT THROUGH TOP OF HORIZONTAL BUNK BOARD PRIOR TO WRAPPING. REQUIRES ONE EACH 5/16" GALV HARDWARE (NOT INCLUDED) - PY1404 NUT, PY1503 FLAT WASHER, PY1592 LOCK WASHER

PY1540 ~ BEVELED WASHER 1/2"

REPRESENTATION PHOTO MAGIC TILT BEVELED WASHER ~ PY1540 USED ON EACH SIDE OF FRAME THRU-BOLT(S) WHERE THE FRAME MEETS THE TONGUE SOLD INDIVIDUALLY

PY1701 ~ SQUARE SCREW 1/2" x 1-1/2" STAINLESS STEEL

REPRESENTATION PHOTO MAGIC TILT SQUARE HEAD SCREW ~ PY1701 USED TO FASTEN ALL PARTS UNDERNEATH CA SERIES TRAILERS W/ SLIDE CHANNELS IT IS RECOMMENDED TO APPLY NEVER-SEIZE TO STAINLESS THREADS TO PREVENT GALLING

PY9040-1 ~ REAR CROSSMEMBER HARDWARE KIT STAINLESS STEEL

REPRESENTATION PHOTO MAGIC TILT CROSSMEMBER HARDWARE KIT ~ PY9040-1 INCLUDES: 4 x PY0491 - SELF TAP SCREW (FOR RUB PAD) 4 x PY1710 - BOLT SS 3/8" x 1-1/4" 4 x PY1820 - NUT NYLOCK SS 1/2" 4 x PY1905 - FLAT WASHER SS 1/2" 2 x PY2540 - U-BOLT SS 1/2" x 3-1/16" x 4-5/16" 12 x PY1810 - NUT NYLOCK SS 3/8" (8 FOR GUIDE POLES) 12 x PY1902 - FLAT WASHER SS 3/8" (8 FOR GUIDE POLES) 4 x PY2500 - U-BOLT SS 3/8" x 1-9/16" x 2-5/8" (FOR GUIDE POLES)

PY9045-1 ~ MID CROSSMEMBER HARDWARE KIT STAINLESS STEEL

REPRESENTATION PHOTO MAGIC TILT CROSSMEMBER HARDWARE KIT ~ PY9045-1 INCLUDES: 4 x PY0491 - SELF TAP SCREW (FOR RUB PAD) 4 x PY1710 - BOLT SS 3/8 x 1-1/4 8 x PY1810 - NUT NYLOCK SS 3/8 16 x PY1902 - FLAT WASHER SS 3/8 4 x PY1725 - BOLT SS 3/8 x 4

RM-U-Bolt Kits (Minimum Order of 20 Each)

11 sizes available

Roll Brackets

5" TONGUE BRACKET ONLY

Single Eye Spring

8 sizes available

SPINDLE NUT

AXLE NUT 3/4" ID

Spindles

2 sizes available

Spring Tabs

3 sizes available

Stabilizer Jack

STABILIZER JACK [11-1/2"]

Stainless Hex Nuts

3 sizes available

Stainless Ni-Lock Nuts

3 sizes available

Stainless Steel Flat Washers

3 sizes available

Desc

Stainless Steel Hex Head Screws

SCREW HX HD S/S 3/8X1 1/4

Stainless Steel Lock Washers

3 sizes available

Desc

Swing Tongue Assemblies

3 sizes available

3X3X24" SWING TONGUE ASSEMBLY SWING TONGUE RR 3X3X4' W/PIVOT BOX SWING TONGUE HTCH PIN 5/8X5"

Swing Tongue Pivot Boxes

3 sizes available

MaterialGalvanized BrandUFP

Tongue Jacks

SWIVEL MOUNT 1000# DL

SKU: PV1155

Undercarriage Angles for Tandem Axle

4 sizes available

XB4291 ~ CROSSMEMBER GALVANIZED 3" x 3" x UP TO 79-1/2" VEE

REPRESENTATION PHOTO MAGIC TILT CROSSMEMBER ~ XB4291 SELECT LENGTH IN DROP-DOWN LENGTH IS STRAIGHT-LINE ACROSS MOUNTING HARDWARE SOLD SEPARATELY CUT ENDS WILL NOT BE HOT-DIPPED GALVANIZED DOES NOT HAVE ANY PRE-DRILLED HOLES END CAPS NOT INCLUDED

XB4293 ~ CROSSMEMBER GALVANIZED 3" x 3" x 80" TO 82" VEE

REPRESENTATION PHOTO MAGIC TILT CROSSMEMBER ~ XB4293 SELECT LENGTH IN DROP-DOWN LENGTH IS STRAIGHT-LINE ACROSS MOUNTING HARDWARE SOLD SEPARATELY CUT ENDS WILL NOT BE HOT-DIPPED GALVANIZED DOES NOT HAVE ANY PRE-DRILLED HOLES END PLUGS NOT INCLUDED

ZZ-PK1560 ~ SUSPENSION BUSHING

RPERESENTATION PHOTO MAGIC TILT SUSPENSION BUSHING ~ ZZ-PK1560 MAY SHIP SEPARATELY FROM STORE